10-29-2012
ifconfig eth0 unplumb equivalent
ifconfig eth0 unplumb will perfectly work on solaris , but linux dont support unplumb option ..what is the correct way to remove the interface , forgive me if this topic is already discussed ..
i tried this
rename /etc/sysconfig/network-scripts/ifcfg-eth0 & restart the network service .. but is not helping .
10 More Discussions You Might Find Interesting
1. IP Networking
Hi there guys!
I have a small task that I have to accomplish, but I don't seem to be able to do that.
I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to... (1 Reply)
Discussion started by: D-Lexy
1 Replies
2. UNIX for Dummies Questions & Answers
if i have the command ifconfig eth0, what will the output be and how can i use either awk or grep to isolate and display the IP address, subnet mask and physical address of my host (1 Reply)
Discussion started by: carlvernon
1 Replies
3. IP Networking
I saw an example on the web, it is an HP-UX command:
ifconfig lan0 unplumb
ifconfig lan0 plumb
so what is plumb actually, I check HP-UX man page and still no idea.
What is the difference if I do in this way?
ifconfig lan0 down
ifconfig lan0 up
:confused: (1 Reply)
Discussion started by: tommy_cs
1 Replies
4. Red Hat
when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in
/etc/sysconfig/network-scripts/.
what will i do? (2 Replies)
Discussion started by: kenshinhimura
2 Replies
5. UNIX for Dummies Questions & Answers
Hi,
Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0?
Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies
6. Red Hat
Hi,
I have just installed RHEL 5.4 on a BL430c-class server and I am attempting to connect to the network only when I try and start eth0, I get the following error?
"Bringing up Interface eth0: hp device eth0 does not seem to be present, delaying initialization."
I am using a HP... (18 Replies)
Discussion started by: Duffs22
18 Replies
7. Red Hat
Hello,
I re-installed my laptop and installed a new copy of VMBOX, I created a VM Machine with my Rhel5 and a CEntos copy as well.
I am using a laptop HP DV4, I use wireless on the laptop.
Usually when I boot up in to either machine I would get eht0 and lo as usual now I just don't get... (4 Replies)
Discussion started by: NelsonC
4 Replies
8. Red Hat
Hi,
I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine.
I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows:
Settings for eth0:
Supported ports: ... (12 Replies)
Discussion started by: Duffs22
12 Replies
9. IP Networking
Hi all,
I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic.
I need to achieve this by editing... (4 Replies)
Discussion started by: landossa
4 Replies
10. Red Hat
Hi guys,
I really need your help with this.
My network interface eth0 is up but not running. I checked udev rules and ifcfg-eth0 files to make sure the mac address are the same.
It just would not come up. Please please I will really appreciate the help here.
Thank you in advance. (3 Replies)
Discussion started by: cjashu
3 Replies