10-29-2012
tell a bit more... what kind of server? how are the disks connected and how are the pools build? from the commands send and receive we can not say anything... would all be speculations.
if this is a hardware issue, we need to know EVERYTHING about the hardware!
10 More Discussions You Might Find Interesting
1. IP Networking
Requirements:
A server program should read a file and send the message to the client . if the file is not there, then switch to the receive part of the same program and receive any messages from the socket. If no messages to receive then switch to send part of the program to... (2 Replies)
Discussion started by: Rajeshsu
2 Replies
2. UNIX for Dummies Questions & Answers
Hi all,
First post!
I have just discovered that I can use unix to send mail to a mail address. I normally use entourage for my mail.
This unix mail is very intriguing to me, but something is not working... I tried the search, but could not find the answer...
This works:
(in terminal)... (1 Reply)
Discussion started by: bjorn
1 Replies
3. UNIX for Dummies Questions & Answers
Hi,
One of the users in our company can send but not receive email. We are using SENDMAIL in conjunction with procmail. The funny thing is that all his sent email is in his /var/spool/mail but the email client does not pick anything up! He is using IMAP.
Anyone see have any ideas? (2 Replies)
Discussion started by: mojoman
2 Replies
4. Programming
Dear friends,
How do I find the TCP send and receive buffer size? (1 Reply)
Discussion started by: nagalenoj
1 Replies
5. Shell Programming and Scripting
Hello,
I need to create a script to monitor sent/received packets for a period of time (the period of time will be a users input) and write the result to some txt file.
Is there any command (don`t want to use any 3rd party sw) what I can use?
I`m using Solaris 10.
Thank you (14 Replies)
Discussion started by: msojka77
14 Replies
6. Shell Programming and Scripting
Hi All,
I am writing one script to automate one long process. In this process we need to upload some input files and download some output files. So , I want to automate this upload and download by using mail functionality.
I want to trigger this script when I am sending mail to server. I know... (0 Replies)
Discussion started by: NirajThakar
0 Replies
7. Solaris
I have two servers, we'll call them sv1 and sv2.
both are Solaris 11.1 LDOMS running on a T4-4 with RBAC enabled.
my user has zfs allow send, receive on both servers and has ssh keys shared.
on sv2 (the destination) I have a zpool called zones that has no zfs fs built
on sv1 (the source) I... (5 Replies)
Discussion started by: os2mac
5 Replies
8. Solaris
trying to clone a zfs file system on the same system using
zfs send -r root/branch@snapshot |zfs receive root/newbranch and get the following error :parent does not exist. How do I fix this? (1 Reply)
Discussion started by: os2mac
1 Replies
9. Shell Programming and Scripting
i have connected with my board through serial interface using minicom and i am running a bash script, which should test ethernet (ping test), USB read/write, RS232 ..
I have managed to test ethernet and USB read/write.
I test ethernet with ping.
I test USB read/write, using dd and verifying... (10 Replies)
Discussion started by: linuxmember
10 Replies
10. Solaris
Good morning everyone,
I'm looking for some help to retrieve data in a scenario where I might have made a big mistake. I'm hoping to understand what I did wrong.
My system is made of two Solaris 11 Express servers (old free version for evaluation). The first if for data and the second is... (7 Replies)
Discussion started by: rnd
7 Replies
LEARN ABOUT OPENSOLARIS
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)
NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [-a blkno [blkno]...] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option can-
not be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.11 24 Feb 1998 addbadsec(1M)