Hello,
I've moved to a new network with multiple AIX box's. Most of them are working fine and dandy.
On one box I need to set up a static route to a gateway.. no problem right?
Whenever I add the route it appears in the routing table as UGc and then begins adding new entries to the... (1 Reply)
I have a string as "Period= 20090531 Client Name= Clayton Lumbar Company Destination= MD"
I want to parse the string and store it in 3 different variables.
$period (should get value 20090531)
$client (should get value "Clayton Lumbar company")
$dest (should get value MD)
How can I do... (3 Replies)
I have an IP routing issue or I am just to stupid to work it out myself.
I have setup am old PC running SUSE Linux 11.3 as a router, the system has 3 Interfaces connecting 3 networks.
Interface 1 = 10.164.2.161/21
Interface 2 = 192.168.1.210/24
Interface 3 = 30.1.0.11/16
The default... (6 Replies)
I have run into a wall troubleshooting a Centos 5 networking issue. Hoping someone can assist.
I've got a box with two vlans trunked over bond0
bond0 Link encap:Ethernet HWaddr 00:22:64:C1:D6:60
inet6 addr: fe80::222:64ff:fec1:d660/64 Scope:Link ... (0 Replies)
hello everyone!:)
I have an exercise which I think is difficult for beginner like me. Here is the exercise
Create a shell script, which takes a directory as command line argument.
Script displays ten first lines from every text file in that directory. After
displaying the lines from the... (1 Reply)
hi guys
suse 11 SP1 x64
I have a server (4 NIC ports 192.168.100.100-103) that connects point to point to a storage device (same thing 4 ports 192.168.110.100-113) but this server connects to normal LAN 10.6.100.x - gateway 10.6.100.1
the issue is when testing connectivity to the storage... (7 Replies)
we are not able to ping client server (falcon-ebr.sbms.bsc.com) from netbackup master server (135.179.96.122 tsprd-ebr.edc.single.net)
However from client server we are able to ping the master Server.
Please assist on this (1 Reply)
Hi,
Please help me on issue described below,
I have 4 machine setup, M1 -> M2 -> M3 | M4. And A laptop that can be reachable through both M3 and M4.
M2 has 2 NIC conected to M3 and M4. Now I want to divide the flow coming from M1 for laptop.
At M2, I have done following,... (1 Reply)
Discussion started by: rahulbhansali24
1 Replies
LEARN ABOUT SUSE
ifsysctl
IFSYSCTL(5) Network configuration IFSYSCTL(5)NAME
ifsysctl[-<interface name>] - per network interface sysctl settings
SYNOPSIS
/etc/sysconfig/network/ifsysctl
/etc/sysconfig/network/ifsysctl-<interface name>
DESCRIPTION
These files are intended to contain sysctl settings, that should be applied when a network interface is created. This are usually interface
specific settings, like:
net.ipv6.conf.eth0.use_tempaddr = 1
or
net.ipv4.conf.eth0.rp_filter = 0
The settings are applied by the /etc/sysconfig/network/scripts/ifup-sysctl script executed via /etc/udev/rules.d/77-network.rules rule (see
udev(7)), after the creation and after the rename of the interface name to its persistent name (when applicable), but before the ifup
<interface name> -o hotplug may be executed to configure the interface.
The settings are not applied by default when the NetworkManager is active (NETWORKMANAGER=yes), except when the IFSYSCTL_NETWORKMANAGER=yes
variable is set in the /etc/sysconfig/network/config file.
Settings from the ifsysctl- file are applied every time an interface has been created.
Settings from the ifsysctl-interface name file are applied when the interface with the corresponding interface name has been created.
SYNTAX
The sysctl(8) utility is required to apply the settings. It supports two separator characters for sysctl keywords: a "." in default format
and a "/" in the alternate format. Therefore the syntax is basically same to the /etc/sysctl.conf file.
Interface names may contain a ".". In the default sysctl format using a "." as separator, that is any "." in the interface name of the key-
word, has to be replaced with a "/". In the alternate sysctl format with "/" as separator, normal interface names can be used.
Optionally, the ifsysctl files may contain also the $INTERFACE and the $SYSCTL_IF variables, that are automatically replaced with the cur-
rent interface name usable in the alternate format and with the sysctl-quoted interface name for the default format, before the settings
are passed to the sysctl utility.
Note also, that settings with variables in the ifsysctl (without the -<interface name> suffix), will be applied for every interface!
Further, files with variables are not compatible to the /etc/sysctl.conf file.
EXAMPLES
Settings for "eth0" and "eth0.1" interfaces
# using "." as separator:
net.ipv6.conf.eth0.use_tempaddr = 1
net.ipv6.conf.eth0/1.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/eth0/use_tempaddr = 1
net/ipv6/conf/eth0.0/use_tempaddr = 1
Settings with variables:
# using "." as separator:
net.ipv6.conf.$SYSCTL_IF.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/$INTERFACE/use_tempaddr = 1
To test your ifsysctl-eth0 or ifsysctl file, use:
/etc/sysconfig/network/scripts/ifup-sysctl eth0 -o debug
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO ifup(8)ifcfg(5)sysctl(8)sysconfig December 2009 IFSYSCTL(5)