10-22-2012
Did you bring the interface up.
Also if issue remains try different port. If using eth0, try eth1.
This User Gave Thanks to ikn3 For This Post:
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
3. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
4. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
5. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
9. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT MINIX
tc-matchall
Match-all classifier in tc(8) Linux Match-all classifier in tc(8)
NAME
matchall - traffic control filter that matches every packet
SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ]
DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
skip_sw
Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter-
face, operation will fail.
skip_hw
Do not process filter by hardware.
EXAMPLES
To create ingress mirroring from port eth1 to port eth2:
tc qdisc add dev eth1 handle ffff: ingress
tc filter add dev eth1 parent ffff:
matchall skip_sw
action mirred egress mirror
dev eth2
The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that
mirrors the packets to device eth2.
To create egress mirroring from port eth1 to port eth2:
tc qdisc add dev eth1 handle 1: root prio
tc filter add dev eth1 parent 1:
matchall skip_sw
action mirred egress mirror
dev eth2
The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a
matchall filters on it that mirrors the packets to device eth2.
To sample one of every 100 packets flowing into interface eth0 to psample group 12:
tc qdisc add dev eth0 handle ffff: ingress
tc filter add dev eth0 parent ffff: matchall
action sample rate 100 group 12
SEE ALSO
tc(8),
iproute2 21 Oct 2015 Match-all classifier in tc(8)