NIC card issue Post: 302713839

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake...

2. HP-UX

configuring nic card

using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ?

3. Linux

Howto Detect New Nic Card

Hi PPL! I have P-IV processor, with on-board NIC card. I have added one more NIC card for domestic use. My kudzu does not recognise the newly added PCMCIA NIC card. How to go about this one? Suggest PEnguin

4. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

5. Solaris

Reg. NIC card

Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than...

6. UNIX for Dummies Questions & Answers

NIC card monitoring traffic question

Folks; I have 2 NIC cards on my SUSE Linux server. One of them was reporting receive errors for a while now it's OK, but i'd like to monitor it. Is there any command i can run to tell me the usage in the past or give me a history of traffic and the speed that going on this specific card? I...

7. Solaris

NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2 When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously. Following are the message log. ifmsdb1 in.mpathd: NIC failure detected...

8. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj

9. Linux

How to check which NIC Card is used for backups?

I have a linux box with 2 nic cards on it one for prod and one for backup. My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion.

10. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out?

LEARN ABOUT DEBIAN

yellowfin-diag

YELLOWFIN-DIAG(8)					      System Manager's Manual						 YELLOWFIN-DIAG(8)

NAME

       yellowfin-diag - EEPROM setup and diagnostic program for Ethernet cards based on the "Yellowfin" G-NIC-I chip.

SYNOPSIS

       yellowfin-diag [options]

DESCRIPTION

       yellowfin-diag  is  a  program that you can use to diagnose problems with Ethernet cards based on the "Yellowfin" G-NIC-I or Symbios 53c885
       chip.

OPTIONS

       These programs follow the usual GNU command line syntax, with long options starting with  two  dashes  (`-').   A  summary  of  options	is
       included below.

       -h, --help
	      Show summary of options.

       -V, --version
	      Show version of program.

       -v, --verbose
	      Verbose mode.

       -q, --quiet
	      Be very unverbose.

       -# <cardnum>
	      Use card number <cardnum>.

       -a, --show_all_registers
	      Print all registers.

       -e, --show-eeprom
	      Dump EEPROM contents to stdout.

       -E, --emergency-rewrite
	      Re-write a corrupted EEPROM.

       -p, --base-address <port>
	      Specify port to use.

       -A, --Advertise <mediaype>
	      Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD.

       -F, --new-interface <interface>
	      Interface  number.  Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
	      100baseFx-FDX, MII and Autosense.

       -H, --new-hwaddress <address>
	      Set card to a new hardware address.

       -m, --show-mii
	      Dump MII management registers.

       -R, --reset
	      Reset the transceiver.

       -T, --test
	      Do register and SRAM test.

       -w, --write-EEPROM <values>
	      Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!

       -f, --force-detection
	      Try to identify the card, even if it is active.

       -t, --chip-type <card>
	      Explicitly set the chip. To get all valid numbers, run yellowfin-diag with the options '-t -1'.

SEE ALSO

       mii-diag(8)

AUTHOR

       yellowfin-diag was written and is still maintained by Donald Becker <becker@scyld.com>.	This manual page was written  by  Alain  Schroeder
       <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).

								 February 18, 2002						 YELLOWFIN-DIAG(8)