Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Folks;
I have 2 NIC cards on my SUSE Linux server. One of them was reporting receive errors for a while now it's OK, but i'd like to monitor it.
Is there any command i can run to tell me the usage in the past or give me a history of traffic and the speed that going on this specific card?
I... (1 Reply)
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT HPUX
dhcpv6db2conf
dhcpv6db2conf(1M)dhcpv6db2conf(1M)NAME
dhcpv6db2conf - DHCPv6 client database converter
SYNOPSIS
[lan_interfaces]
DESCRIPTION
provides a means of translating the DHCPv6 client database, into a set of standard configuration file variables. The client database con-
sists of a series of records. Each record represents a unique lan interface and a list of attributes, which correspond to that interface.
The attributes are configuration parameters like: host's IP address, NTP server address, address of the DHCPv6 server, NIS domain name etc
for that interface. With you can list the contents of the database to the screen, create a set of configuration staging files, or execute
direct edits on existing configuration files using the values contained in the client database.
Options
allows you to specify a list of lan interfaces on the command line (e.g. whose data needs to be translated to a readable format. If no
lan interface is specified, will process the entries of all interfaces which are UP. The attributes can be selected for processing by
specifying a combination of one or more filter flags on the command line. If no filter flag is specified, all the attributes for that lan
interface will be processed.
The following options are supported:
Using the results of the specified filter, directly apply the variable
definitions to the existing configuration files (for example,
Create a set of staging files using the results of the selected filter(s).
Each variable processed will be applied to its corresponding staging configuration file.
Specifically, will generate a copy of the existing configuration file. For example, will be copied to Once this staging
file has been created, the variable that is being processed will be applied to this newly created file.
Print results to the screen (stdout), this is the default action if neither
nor are specified.
Process the INTERFACE variable set [IPV6_SECONDARY_INTERFACE_NAME, IPV6_ADDRESS, IPV6_PREFIXLEN, DHCPV6_ENABLE].
Process the DNS variable set
[domain, nameserver].
Process the SIP server address and SIP domain name information.
Process the NIS variable set
[NIS_DOMAIN, YPSET_ADDR].
Process the vendor specific information.
Print the DHCPv6 server address.
lan_interfaces lan interfaces such as whose data needs to be translated to a readable format. If not specified, will process the entries
of all interfaces which are UP.
Configuration Files and Variable Names
The following files and variables can be processed:
IPV6_SECONDARY_INTERFACE_NAME
IPV6_ADDRESS
IPV6_PREFIXLEN
DHCPV6_ENABLE
NIS_DOMAIN
YPSET_ADDR
domain / search
nameserver
EXAMPLES
To list the entire contents of the DHCP client database type:
To list only the INTERFACE variable set for type:
AUTHOR
was developed by Hewlett-Packard.
FILES
Client configuration database
SEE ALSO dhcpv6clientd(1M), dhcpv6client_ui(1), dhcpv6d(1M).
dhcpv6db2conf(1M)