Sponsored Content
Operating Systems Solaris ntp client configuration error Post 302713793 by DGPickett on Thursday 11th of October 2012 10:06:35 AM
Old 10-11-2012
traceroute has some nice options for specifying the protocol and port to test access to.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

ntp configuration

Hi all, I'm sure this question was asked before but I couldn't find what I was looking for in the 2 threads I found on here. Here's my question/problem: I have an isolated (no connection to outside world at all) Unix network. I want to have time sync between my other non-PC based system... (0 Replies)
Discussion started by: mariobernier
0 Replies

2. Windows & DOS: Issues & Discussions

ntp client windows xp

All, I have a Windows XP client which I need to get time synchronized from a Linux ntp server. What are the commands to perform the setup and configuration? Thanks, Mike (1 Reply)
Discussion started by: bubba112557
1 Replies

3. Solaris

ntp server and ntp client

All, How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server. Any... (1 Reply)
Discussion started by: bubba112557
1 Replies

4. Red Hat

NTP Configuration on RHEL 5.4

Hi, I'm trying to configure NTP client, however it failes to sync correctly. Even after I manually set the time, once it connects with the NTP server, it pushes the time ahead by 4 hours. We have set an AIX host as NTP server. It works fine for other AIX hosts, however fails on RHEL 5.4 ... (4 Replies)
Discussion started by: max_min
4 Replies

5. Solaris

ntp server configuration

hi Please give me the configuration steps for NTP server. How do i sync other servers with this NTP server thanks to all (1 Reply)
Discussion started by: sijocg
1 Replies

6. Solaris

NTP client offset

How to add offset to NTP client so that, for eg., clock is -20 seconds? (2 Replies)
Discussion started by: orange47
2 Replies

7. UNIX for Dummies Questions & Answers

NTP configuration issue..

hello Guys, I have an NTP problem on my SUN N240 server. External NTP server is being used for this box and when i run 'ntpq -p' i get connection refused message; ntpq -p ntpq: read: Connection refused Here this is the ntp.conf file: cat /etc/ntp.conf # BEGIN NTP SERVERS server... (6 Replies)
Discussion started by: dyavuzy1
6 Replies

8. Red Hat

NTP Configuration file

Hi, Could you please explain about "restrict" parameters in /etc/ntp.conf in ntp client and ntp Servers. Example: restrict 127.0.0.1 restrict -6 ::1 restrict 192.168.1.0 mask 255.255.255.0 nomodify notrap Regards, Mastan (1 Reply)
Discussion started by: mastansaheb
1 Replies

9. Red Hat

Yum client configuration error

Dear concern, I want to configure a yum client node. Yum configuration file (/etc/yum.repos.d/) is given below: # cat server.repo name=rhel6 baseurl=ftp://192.168.225.3/pub/Packages/ enabled=1 gpgcheck=0 We got following error message while executing yum list command. # yum clean... (1 Reply)
Discussion started by: makauser
1 Replies

10. Red Hat

Ntp client sync with local over ntp server

Hi, I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local? # ntpq -p ... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
TRACEROUTE6(8)						 System Manager's Manual: iputils					    TRACEROUTE6(8)

NAME
traceroute6 - traces path to a network host SYNOPSIS
traceroute6 [-dnrvV] [-i interface] [-m max_ttl] [-p port] [-q max_probes] [-s source] [-w wait time] destination [size] DESCRIPTION
Description can be found in traceroute(8), all the references to IP replaced to IPv6. It is needless to copy the description from there. SEE ALSO
traceroute(8), tracepath(8), ping(8). HISTORY
This program has long history. Author of traceroute is Van Jacobson and it first appeared in 1988. This clone is based on a port of tracer- oute to IPv6 published in NRL IPv6 distribution in 1996. In turn, it was ported to Linux by Pedro Roque. After this it was kept in sync by Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>. And eventually entered iputils package. SECURITY
tracepath6 requires CAP_NET_RAW capability to be executed. It is safe to be used as set-uid root. AVAILABILITY
traceroute6 is part of iputils package and the latest versions are available in source form at http://www.skbuff.net/iputils/iputils-cur- rent.tar.bz2. iputils-161105 09 March 2017 TRACEROUTE6(8)
All times are GMT -4. The time now is 06:53 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy