Your system seems to be complaining about a couple of network interfaces which are either really faulty or have been flagged as faulty in error.
In the service processor (SP>) try clearfault and clearasrdb commands.
Then try booting.
If that fails try shutting the system down completely (unplug power) and then reconnect. Watch the SP start up and whether it marks these devices as bad (error messages). If they are marked bad:
then try boot.
I've seen this work despite the devices being marked bad during SP boot. If this works the most likely cause is a daughterboard containing these interfaces needs reseating (poor electrical contact issue).
Hope that helps.
---------- Post updated at 10:40 PM ---------- Previous update was at 10:21 PM ----------
Hi, i was installing solaris 8 on sunfire v250 and the power fails :mad: , now it does not boot from cd rom and get the next msg:
ð
Sun Fire V120 (UltraSPARC-IIe 648MHz), No Keyboard
OpenBoot 4.0, 512 MB memory installed, Serial #56338483.
Ethernet address 0:3:ba:5b:a8:33, Host ID: 835ba833.
... (1 Reply)
I have a machine running HP-UX 11.23 (PARISC) and APA startup fails on boot. This is found in /etc/rc.log:
Configure Auto-Port Aggregation(LAN Monitor) interfaces
Output from "/sbin/rc2.d/S343hplm start":
----------------------------
get_start_dlpi_version: failed, errno is 22
ERROR: ... (1 Reply)
Hi,
I am trying to setup a server for a diskless boot of a computer class (with ubuntu)
I followed the guidelines in https://help.ubuntu.com/community/DisklessUbuntuHowto
I have two computers: one is the server I installed and the other is my macbook on which I run a virtual machine... (8 Replies)
I have three Sun Oracle Netra T5220s. I am trying to just get the processor information psrinfo or prtdiag -v from the # prompt in single user mode.
I am needing to know the commands to get to boot the CD/DVD of the Solaris OS. I am using it via Serial Port Management.
Tinkering around I... (4 Replies)
I have a T2000 enterprise SPARC server that's no longer on contract with Oracle. It's on old firmware (6.3.x). After a power-down this weekend, it won't boot normally. Boot snapshot at the bottom of the post.
It can boot to cdrom, and it'll boot to failsafe mode, but it won't do a regular... (9 Replies)
I have an m5000 that Is down.
I have access to XSCF>
and was able to get to the ok prompt.
However, on
>ok boot
it failed to boot.
erred with :
svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL.
Nov 29... (3 Replies)
My OS solarius 5.10 Generic_147148-2 i86
Error: please review new boots environments using options
1. Solution - show me the commands
Partition is full, try to remove some unneeded files,
then try to compress some other unneeded files.
man command creates a temp file under... (0 Replies)
My system suddenly crash and when it rebooted there was an error:
/dev/rdsk/c1t0d0s3 is logging
svc.startd: svc:/network/nis/client:default: Method "/method/yp" failed with status 96.
The system completes booting however when I log in a user account / directory is not longer... (1 Reply)
Hi,
I want to install Solaris-11 on T5220. I created USB from sol-11_4-text-sparc.usb by usbcopy on another Solaris-11 servers, which looks like a good one.
I tried did "reset-all" and still same issue. Can I get some help on this.
{0} ok reset-all
Sun Netra T5220, No Keyboard
Copyright... (8 Replies)
hi:)
i can't boot my sun server by iso solaris 10 sparc dvd that i did download from oracle site.
my hardware is sun T5220.
i receive these after running boot cdrom -s :
can't read disk lable
can't open disk lable package
ERROR: boot-read fail
whould u help me?
Please use CODE... (1 Reply)
Discussion started by: Arefdel
1 Replies
LEARN ABOUT MOJAVE
httppower
httppower(8) powerman httppower(8)NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS -u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)