@nextyoyoma:
will write 2000 lines into output2, not 1000 as requestedd per OP. Similarly the third awk command.
@OP:
If you have split(1) it's trivial:
On my system, the default is to split every 1000 lines, so actually all you'd need is
but check man split for your implementation.
If you don't have split, here is an awk solution:
It will create files
etc.
Hi there,
I need to split one huge file into separate files if the condition is fulfilled according to that the position between 97 and 98 matches with “IT” at the segment MAS. There is no delimiter file is fix-width with varous line length.
Could you please help me how I do split the file... (1 Reply)
All,
We receive a file with a large no of records (records can vary) and we have to split it into two files based on another file. e.g.
File1:
UHDR 2008112
"25187","00000022","00",21-APR-1991,"" ,"D",-000000519,+0000000000,"C", ,+000000000,+000000000,000000000,"2","" ,21-APR-1991... (7 Replies)
Hi ,
I have one file which has many headers.
Say suppose
HEDAER
..data DATA DATA
..data
..data
HEADER
..data
..data
DATA
.data
HEADER.
..data
..data
If there are 3 HEADERS in source file then I need to split the source file into 3 separate file.... (2 Replies)
Hi All,
I have a rather stange set of requirements that I'm hoping someone here could help me with. We receive a file that is actually a concatenation of 4 files (don't believe this would change, but ideally the solution would handle n files).
The super-file looks like:... (7 Replies)
Dear All,
I have two files but want to extract data from one based on another... can you please help me
file 1
David
Tom
Ellen
and file 2
David|0010|testnamez|resultsz
David|0004|testnamex|resultsx
Tom|0010|testnamez|resultsz
Tom|0004|testnamex|resultsx
Ellen|0010|testnamez|resultsz... (12 Replies)
Hi All,
I have more than half million lines of XML file , wanted to split in four files in a such a way that top 7 lines should be present in each file on top and bottom line of should be present in each file at bottom.
from the 8th line actual record starts and each record contains 15 lines... (14 Replies)
hdr=$(cut -c1 $path$file|head -1)#extract header”H”
trl=$(cut -c|path$file|tail -1)#extract trailer “T”
SplitFile=$(cut -c 50-250 $path 1$newfile |sed'$/ *$//' head -1')# to trim white space and extract table name
If; then # start loop if it is a header
While read I #read file
Do... (4 Replies)
Hi ,
I am having a scenario where I need to split the file based on two field values. The file is a fixed length file.
ex:
AA0998703000000000000190510095350019500010005101980301
K 0998703000000000000190510095351019500020005101480 ... (4 Replies)
Discussion started by: saj
4 Replies
LEARN ABOUT DEBIAN
record
record(1) General Commands Manual record(1)NAME
record - records *.wav files
SYNOPSIS
record [ options ]
DESCRIPTION
record records *.wav files in CD quality (i.e. 44100 Hz, 16bit, stereo). It has a input level meter, which might be useful for sound trou-
ble shooting (check if the mixer settings ok for recording from the TV card etc.)
OPTIONS -h display help text
-o file
basename for the output file(s), a number and the .wav extension are added by record. Default is "record".
-i dev mixer control. This should be the one where you can adjust the record level for your audio source. Default is "line". "mic" and
"igain" are good candidates too. Best way to figure is to start your favorite mixer tool and check out which one works ...
-m dev set mixer device. Default is "/dev/mixer".
-d dev set audio device. Default is "/dev/dsp".
-r rate
set sample rate. Default is 44100.
-p sec peak seconds (number of seconds which should be scanned for the volume maximum). This affects both peak level display and level
triggered recording (see below). Default is 1.5 seconds.
record can also be used non-interactive:
-c enable console (non-interactive) mode.
-v be verbose (console mode only).
-t mm:ss
Limit the record time (console mode only). By default record records until stopped by a signal (by typing ^C for example).
-s size
Limit the file size (console mode only). record will continue with a new file once the limit is reached.
-n num Limit the file count (console mode only). record will stop recording after num files.
-l Enable level triggered recording (console mode only) with the default trigger level (1000).
-L level
Enable level triggered recording with the specified trigger level.
If level triggered recording is active, record will start and stop recording depending on the signal strength. Recording will be started
if the signal strength is above the trigger level (1000/32768 => around 3%). Recording will be stopped if the signal is below the trigger
level for some time (1.5 seconds by default, the -p switch changes this).
AUTHOR
Gerd Knorr <kraxel@bytesex.org>
(c) Gerd Knorr record(1)