CHECK SCRIPT SYNTAX Post: 302703151

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

syntax and semantic check

Does the shell perform a syntax and semantic check before commands are sent to the kernel? Ravioli

2. UNIX for Dummies Questions & Answers

I've made an awk command that works successfully. However I'd like to add one character to it. For example instead of /what_i_have_now/ I'd like to change just ONE field to the opposite with an exclamation point. Like this: ! /what_i_have_now/ My question, where am I supposed to place...

3. UNIX for Dummies Questions & Answers

Script to check for a file, check for 2hrs. then quit

I wish to seach a Dir for a specific file, once the file is found i will perform additional logic. If the file is not found within two hours, i would like to exit. Logically, I'm looking for the best way to approach this Thanks for any assistance in advance. Note: I'm using a C shell and...

4. Shell Programming and Scripting

How to Check Shell script syntax w/o executing

Hello All, I looking for a way to verify the correction of shell script syntax. Is there any switch like -c in perl which do this in shell ? Thank You.

5. Shell Programming and Scripting

script to check if another script is running and if so, then sleep for sometime and check again

Hi, I am a unix newbie. I need to write a script to check wheteher another script is still running. If it is, then sleep for 30m and then check again if the script is running. If the script has stopped running then, I need to come out of the loop. I am using RHEL 5.2

6. Shell Programming and Scripting

Syntax error calling TCL script from shell script

hello everyone i am beginner on shell scripting .and i am working on my project work on ad hoc network i wrote a batch (.sh) to do a looping and execute a tcl script i wrote before in each iteration ..but i got this problem " syntax error near unexpected token `('...

7. Shell Programming and Scripting

Shell script check syntax not working ...

Hello i have question that i want check syntax from my script shell with sh -n filename but it's not show something even i have wrong syntax in my file. why can this happened or any other way to check it? i use on header of file : #!/bin/sh thx before :)

8. Shell Programming and Scripting

Help with Check Syntax of Shell Script without Running

Hi Everyone, Is there any way ( generic) to check syntax of Shell Scripts without running it??

9. Shell Programming and Scripting

Script syntax help

#!/bin/bash if ; then echo "Lipsa IP"; exit; fi i=1 ip=$1 while ; do if ; then rand=`head -$i pass_file | tail -1` user=`echo $rand | awk '{print $1}'` pass=`echo $rand | awk '{print $2}'` CMD=`ps -eaf | grep -c mysql` if ; then ./mysql $ip $user $pass & else sleep 15...

LEARN ABOUT HPUX

service

SERVICE(8)                                                    System Manager's Manual                                                   SERVICE(8)

NAME

       service - run a System V init script

SYNOPSIS

       service SCRIPT COMMAND [OPTIONS]

       service --status-all

       service --help | -h | --version

DESCRIPTION

       service  runs  a System V init script or systemd unit in as predictable an environment as possible, removing most environment variables and
       with the current working directory set to /.

       The SCRIPT parameter specifies a System V init script, located in /etc/init.d/SCRIPT, or the name of a systemd unit.  The  existence  of  a
       systemd unit of the same name as a script in /etc/init.d will cause the unit to take precedence over the init.d script.  The supported val-
       ues of COMMAND depend on the invoked script. service passes COMMAND  and OPTIONS to the init script unmodified. For systemd  units,  start,
       stop, status, and reload are passed through to their systemctl/initctl equivalents.

       All scripts should support at least the start and stop commands.  As a special case, if COMMAND is --full-restart, the script is run twice,
       first with the stop command, then with the start command.

       service --status-all runs all init scripts, in alphabetical order, with the status command. The status is [ + ] for running services, [ - ]
       for stopped services and [ ? ] for services without a status command.  This option only calls status for sysvinit jobs.

EXIT CODES

       service calls the init script and returns the status returned by it.

FILES

       /etc/init.d
              The directory containing System V init scripts.

       /{lib,run,etc}/systemd/system
              The directories containing systemd units.

ENVIRONMENT

       LANG,  LANGUAGE,  LC_CTYPE, LC_NUMERIC, LC_TIME, LC_COLLATE, LC_MONETARY, LC_MESSAGES, LC_PAPER, LC_NAME, LC_ADDRESS, LC_TELEPHONE, LC_MEA-
       SUREMENT, LC_IDENTIFICATION, LC_ALL, TERM, PATH
              The only environment variables passed to the init scripts.

SEE ALSO

       /etc/init.d/skeleton
       update-rc.d(8)
       init(8)
       invoke-rc.d(8)
       systemctl(1)

AUTHOR

       Miloslav Trmac <mitr@redhat.com>, Petter Reinholdtsen <pere@hungry.com>

       Licence: GNU Public Licence v2 (GPLv2)

COPYRIGHT

       2006 Red Hat, Inc.,  Petter Reinholdtsen <pere@hungry.com>

Jan 206                                                                                                                                 SERVICE(8)

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

syntax and semantic check

Discussion started by: ravioli

2. UNIX for Dummies Questions & Answers

quick check of my awk syntax

Discussion started by: yongho

3. UNIX for Dummies Questions & Answers

Script to check for a file, check for 2hrs. then quit

Discussion started by: mmarsh