My WS boot disk has failed so when i want to boot system (by OK boot -s or Ok boot disk0 ) i get these mesgs:
disk read error
boot :can not find misc/sparc9v/krtld
boot:error loading interperetor (misc/sparc9v/krtld)
Elf64 read error.
boot failed.
although it's probed ,finally i try... (1 Reply)
Hi All,
Seems to be one of the disk has failed on my Solaris server.
How do i confirm that disk has really failed or not?
Here are alert details.
-------
iostat -En out/put
c1t3d0 Soft Errors: 1884 Hard Errors: 153 Transport Errors: 54
Vendor: FUJITSU Product:... (3 Replies)
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
I have an oldish Solaris 10 system (SunFire x4240), which due to a recent heating event in the server room, lost it's system disk.
I have rsync backups of all the other (data) disks, but apparently I do not have a backup of /. :-( I can start the machine up in failsafe mode, but running fsck on... (4 Replies)
Iam new to AIX
I am unable varyonvg on the vios,some of the disk are reported as harware failure.
I am going to replace the disk,Please tell me how to remove the disk without any corruption in the VG
lspv -l hdiskx also didn't work (0 Replies)
Hi
Please can you help me on replacing or removing a faulty disk drive on a SUN NETRA X4250server with 4 internal drives only.
the format comand show me the following:
format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c0t0d0 <drive type unknown>
... (9 Replies)
Discussion started by: fretagi
9 Replies
LEARN ABOUT HPUX
vxr5check
vxr5check(1M)vxr5check(1M)NAME
vxr5check - verify RAID-5 volume parity
SYNOPSIS
/etc/vx/bin/vxr5check [-i | -v] [-g diskgroup] volume
DESCRIPTION
The vxr5check utility compares the parity of each stripe of a RAID-5 volume specified by volume. vxr5check reads the data for each stripe,
generates the parity for this stripe, and compares this parity with the existing parity.
vxr5check can be run against the entire RAID-5 volume, or incrementally on RAID-5 stripe boundaries, by specifying the -i option.
OPTIONS -g diskgroup
Specifies the Veritas Volume Manager (VxVM) disk group name for the RAID-5 volume name for verification. If this option is not
specified, the default disk group is determined using the rules given in the vxdg(1M) manual page.
-i Verifies the RAID-5 volume incrementally per stripes. If a parity mismatch is found, that stripe location is displayed.
-v Verbose output for the incremental vxr5check verification. The verbose option outputs each stripe number that is being verified.
OUTPUT FORMAT
In verbose mode and incremental mode, summary reports for each stripe of the RAID-5 volume are printed in output records. If an error is
returned for a stripe, then an error message and stripe number are displayed. In non-verbose mode, if an error is returned, an error mes-
sage is displayed.
If a parity mismatch error is determined on a stripe, vxr5check exits on that stripe and does not continue for the remaining stripes in the
RAID-5 volume.
FILES
/usr/lib/vxvm/bin/vxr5vrfy The utility that vxr5check calls to perform RAID-5 parity verification operations for the specified RAID-5
volume.
EXIT CODES
The vxr5check utility exits with a non-zero status if the attempted operation fails. A non-zero exit code is not a complete indicator of
the problems encountered, but rather denotes the first condition that prevented further execution of the utility.
See vxintro(1M) for a list of standard exit codes.
NOTES
Do not run vxr5check on a volume that is in degraded mode.
SEE ALSO vxevac(1M), vxintro(1M), vxmend(1M), vxvol(1M)VxVM 5.0.31.1 24 Mar 2008 vxr5check(1M)