08-31-2012
You need to login to the hardware interface. For example Dell uses the DRAC, whictch can be accessed through a web GUI. On SUN servers you use a ILOM or ALOM, which is also accessible though a web GUI.
In the GUI there will be an option to light up the HD.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
is there anu way by which i can find out if all the disks on the system are working ?
Milind Shauche. (2 Replies)
Discussion started by: shauche
2 Replies
2. HP-UX
I am new to being a Unix admin and have a question about replacing some hardware. I have a K class box using HP-UX 10.20 with three disks. Two of the drives are in one logical volume. Every 3 or 4 days, the syslog is showing that one of these drives is experiencing "POWERFAILED" and then recovering... (6 Replies)
Discussion started by: SemiOfCol
6 Replies
3. Filesystems, Disks and Memory
Hi people, I have been using my disk for quite a long time but the other day I heard the drive making some noise and had to restart the system again. But when I did that the disk would not boot and I fear that the data might be deleted or lost. So, if you people have any know about the ways to get... (1 Reply)
Discussion started by: adam466
1 Replies
4. Filesystems, Disks and Memory
Hi people,
I have been using my disk for quite a long time but the other day I heard the drive making some noise and had to restart the system again. But when I did that the disk would not boot and I fear that the data might be deleted or lost. So, if you people have any know about the ways to... (2 Replies)
Discussion started by: christopher4
2 Replies
5. Solaris
hi all,
have a solaris 9 OS and a SAN disk which used to work fine is not getting picked up by my machine. can anyone point out things to check in order to troubleshoot this ??
thanks in advance. (3 Replies)
Discussion started by: cesarNZ
3 Replies
6. Solaris
I've got an old E250 server where a front error LED is showing. I've read through the Sun docs (Sun Enterprise 250 Server Owner's Guide - Sun Microsystems) but it's only the 'General fault' LED (About the Status and Control Panel (Sun Enterprise 250 Server Owner's Guide) - Sun Microsystems)... (2 Replies)
Discussion started by: aussieos
2 Replies
7. Solaris
Hi,
I have a very frustrating issue! I hope you guys can assist
When a disk is presented out the iSCSI target display a lower disk capacity
SOLARIS VERSION is SOLARIS 10 05/09 Kernel Patch 139555-31
ISCSI Patch 119090-31, 141878-11
Unix Commands To discover Target
bash-3.00# i... (0 Replies)
Discussion started by: capitalexall
0 Replies
8. UNIX for Advanced & Expert Users
Hi there,
Don't know if my title is relevant but I'm dealing with dangerous materials that I don't really know and I'm very afraid to mess anything up.
I have a Debian 5.0.4 server with 4 x 1TB hard drives.
I have the following mdstat
Personalities :
md1 : active raid1 sda1 sdd1... (3 Replies)
Discussion started by: chebarbudo
3 Replies
9. Shell Programming and Scripting
what i should to do next? read full query first please!!
harshbhu@harshbhu:/usr/local/gg/10.6/updates/Source$ sudo ./install_software
sudo: unable to resolve host harshbhu
install_software version 2017/06/29
GAMIT and GLOBK to be installed into /usr/local/gg/10.6/updates/Source
If... (0 Replies)
Discussion started by: ankit lohar
0 Replies
10. AIX
Hi all,
I have encountered the issue with the hard disk, the disk is failed and need to replace by the new one.
As my understanding, this is just to take out the failed disk and insert the new ones, and that's all.
But the third party hardware vendor said, there should be another procedure... (9 Replies)
Discussion started by: Phat
9 Replies
LEARN ABOUT DEBIAN
fiu-run
fiu-run(1) General Commands Manual fiu-run(1)
NAME
fiu-run - a script to launch programs using libfiu
SYNOPSIS
fiu-run [options] program [program arguments]
DESCRIPTION
fiu-run is a script to make it easier to launch programs using libfiu(3). It can enable failure points and start libfiu's remote control
capabilities before starting to execute the program, avoiding the need to write a special launcher to inject failures.
It is specially useful when used to inject failures in the POSIX/libc functions, because it does not require any program modifications.
After launching programs with fiu-run, fiu-ctrl(1) can be used to enable and disable their failure points at runtme.
For additional documentation, go to the project's website at http://blitiri.com.ar/p/libfiu.
OPTIONS
-c command
Run the given libfiu remote control command before executing the program (see below for reference).
-x Use the POSIX libfiu preload library, allows simulate failures in the POSIX and C standard library functions.
-f ctrlpath
Enable remote control over named pipes with the given path as base name, the process id will be appended (defaults to "$TMPDIR/fiu-
ctrl", or "/tmp/fiu-ctrl" if "$TMPDIR" is not set). Set to "" to disable remote control over named pipes.
-l path
Path where to find the libfiu preload libraries. Defaults to the path where they were installed, so it is usually correct.
Remote control commands are of the form "command param1=value1,param2=value2". Valid commands are:
'enable name=NAME'
Enables the NAME failure point unconditionally.
'enable_random name=NAME,probability=P'
Enables the NAME failure point with a probability of P.
All of the enable* commands can also optionally take failnum and failinfo parameters, analogous to the ones taken by the C functions.
EXAMPLES
The following will run the fortune(1) program simulating faults in read() with 5% probability (note that the -x parameter is required in
this case to enable failure points in the POSIX and libc functions):
fiu-run -x -c "enable_random name=posix/io/rw/read,probability=0.05" fortune
By running it multiple times you will see that sometimes it works, but most of the time you get different errors, resulting from the simu-
lated failures.
SEE ALSO
libfiu(3), fiu-ctrl(1).
BUGS
If you want to report bugs, or have any questions or comments, just let me know at albertito@blitiri.com.ar. For more information about
libfiu, you can go to http://blitiri.com.ar/p/libfiu.
16/Jun/2009 fiu-run(1)