08-29-2012
You probably shouldn't use expect for this. Use the
ksh coprocess facility instead. You can simply terminate the coprocess then by issuing
kill -15 %1 or similar from the main process.
I hope this helps.
bakunin
This User Gave Thanks to bakunin For This Post:
10 More Discussions You Might Find Interesting
1. AIX
I wrote a ksh script for Helpdesk. I need to know how to disable ctrl-c,ctrl-z,ctrl-d..... so that helpdesk would not be able to get to system prompt :confused: (6 Replies)
Discussion started by: wtofu
6 Replies
2. Shell Programming and Scripting
Hi I have written one shell script , using that i am able to connect to remote machine but i have to
#!/usr/bin/expect -f
set address
set username
set password
set OOLpath
set dbusername
set dbpasswd
set tnsname
set recdbusername
set recdbpasswd
set rectnsname
spawn ssh... (1 Reply)
Discussion started by: mnmonu
1 Replies
3. Shell Programming and Scripting
Hi,
I have written one shell script , using that i am able to connect to remote machine but i have to
#!/usr/bin/expect -f
set address
set username
set password
set OOLpath
set dbusername
set dbpasswd
set tnsname
set recdbusername
set recdbpasswd
set rectnsname
spawn ssh... (2 Replies)
Discussion started by: mnmonu
2 Replies
4. Shell Programming and Scripting
Greetings,
I am writing an Expect script to automate multiple processes on an HP-UX system. Everything has gone fine so far but I now have run into a problem. One of the processes that I'm trying to automate requires the key combination of ctrl break and I have so far been unable to figure out... (1 Reply)
Discussion started by: g_trueblood2000
1 Replies
5. Shell Programming and Scripting
I have to send few gzipped files from local server to SFTP server.
My Server Info
Distributor ID: Ubuntu Description: Ubuntu 12.04.4 LTS Release: 12.04 Codename: precise
Created a bash script and could able to send files to sftp, but i want to send email if transfer is successful.
... (1 Reply)
Discussion started by: krux_rap
1 Replies
6. Shell Programming and Scripting
declare -a array=( "LLC-load-misses" "LLC-loads" "LLC-store-misses" "LLC-stores" "branch-load-misses" "branch-loads" "dTLB-load-misses" "dTLB-loads" "dTLB-store-misses" "dTLB-stores" "iTLB-load-misses" "iTLB-loads" "branch-instructions" "branch-misses" "bus-cycles" "cache-misses" "cache-references"... (2 Replies)
Discussion started by: BHASKAR JUPUDI
2 Replies
7. Shell Programming and Scripting
Hi,
I am executing a expect script in while loop for doing telnet on list of servers stored in file as below :
expect script :
#!/usr/bin/expect -f
set timeout 20
set ip
set port
if { == 0} {
send_user "Usage: scriptname ip port\n"
exit 1
}
#exp_internal 1
log_user 0
spawn... (3 Replies)
Discussion started by: omkar.jadhav
3 Replies
8. Shell Programming and Scripting
Hi I am trying the following in my bash script which logs into my machine and runs a command. Trying to solve this using expect.
The first expect statement is hit and it enters the address "10.10.0.10" but when the second expect statement is hit it exits
#!/bin/bash
expect -c '
spawn... (2 Replies)
Discussion started by: skorada
2 Replies
9. Shell Programming and Scripting
Hey All,
I am writing one script using expect, that script which is used in spawn will accepts only 1. Enter 2. Ctrl+c
Press Control-C to exit, Enter to proceed.
Could some one share some thoughts to send the above user inputs in linux expect block ?
Thanks,
Sam (0 Replies)
Discussion started by: SCHITIMA
0 Replies
10. UNIX for Beginners Questions & Answers
Dear Tech Guys,
I am trying to send some commands on the local server and it always asks for user name and password after each command. To serve the purpose I am using expect function as follows:
#!/usr/bin/expect
set timeout 20
spawn "./data1.sh"
expect "Please Enter UserName: "... (6 Replies)
Discussion started by: Xtreme
6 Replies
kill(1) General Commands Manual kill(1)
Name
kill - send a signal to a process
Syntax
kill [-sig] processid...
kill -l
Description
The command sends the TERM (terminate, 15) signal to the specified processes. If a signal name or number preceded by `-' is given as first
argument, that signal is sent instead of terminate. For further information, see
The terminate signal kills processes that do not catch the signal; `kill -9 ...' is a sure kill, as the KILL (9) signal cannot be caught.
By convention, if process number 0 is specified, all members in the process group (that is, processes resulting from the current login) are
signaled. This works only if you use and not if you use To kill a process it must either belong to you or you must be superuser.
The process number of an asynchronous process started with `&' is reported by the shell. Process numbers can also be found by using It
allows job specifiers ``%...'' so process ID's are not as often used as arguments. See for details.
Options
-l Lists signal names. The signal names are listed by `kill -l', and are as given in /usr/include/signal.h, stripped of the common SIG
prefix.
See Also
csh(1), ps(1), kill(2), sigvec(2)
kill(1)