08-29-2012
Naveen ,
Verify the MAC address of the Onboard interfaces they will change after your replace the systemboard.
This User Gave Thanks to rama krishna For This Post:
6 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm trying to find information to help me switch to UNIX os from Windows98. Is this where I should be? If so, can someone get me started? I have a Compaq Presario 5030 with a USR 56k modem and other peripherials. Sound card is integrated onto the motherboard (I think). So, I need drivers, etc. Any... (2 Replies)
Discussion started by: leohutt
2 Replies
2. Post Here to Contact Site Administrators and Moderators
Just a remark now the board has grown to considerable proportion. I see too little of an active hand(s) maintaning the boards, clipping away dead posts, moving posts that were created in the wrong forums etc. It's a bit tiring to see alot of threads ending in: this has been covered before, do a... (7 Replies)
Discussion started by: patvdv
7 Replies
3. UNIX for Dummies Questions & Answers
Hi friends i am going to use FEDORA CORE ...Should i need to install Mother Board Drivers ? (1 Reply)
Discussion started by: haisubbu
1 Replies
4. Shell Programming and Scripting
HI all,
I have armv7 board and i will execute script in host machine with ssh connection from board .
I have to test when board in standby mode the script runned in host remain working .
The result is the reverse when kernel is in standby mode on board.
SSH connection closed and the... (3 Replies)
Discussion started by: marwen_joe
3 Replies
5. How to Post in the The UNIX and Linux Forums
Can please somebody tell me what could be the reason for the following error (Unix Motorola Server):
/usr/etc/ce3/s374: Board at address 0xff10000 not present - Entry skipped.
/dev/lpc2: I/O error
I already replaced the board 374 on the server, but I have the same problem.
Thank you! (1 Reply)
Discussion started by: dma
1 Replies
6. OS X (Apple)
Hi guys...
Well I have entered an area of partial insnity... ;o)
Below is a photo of the 'ALTDC' board for AudioScope.sh...
I have decided to incorporate all three methods for obtaining DC into this MBP via the MIC input.
1) VFO.
2) CHOPPER.
3) COUNTER.
The controller for the COUNTER... (9 Replies)
Discussion started by: wisecracker
9 Replies
LEARN ABOUT DEBIAN
setether
SETETHER(8) System Manager's Manual SETETHER(8)
NAME
setether - Set the ethernet address for use with DECnet
SYNOPSIS
setether <if> [<if>...]|all [options]
DESCRIPTION
Set ethernet MAC address on ethernet adaptors
This script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately. If you do
not run setether then you must change the ethernet address in some other way for DECnet to work.
By default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
be changed, otherwise a list of interface names can be specified. setether will enable (UP) all interfaces it changes the MAC addresses
of.
(2.4 only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
contact nodes not in the neighbour table will be done over this interface).
This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.
EXAMPLES
set the MAC address of eth0.
# /sbin/setether eth0
set the MAC address of all ethernet interfaces
# /sbin/setether all
HELPFUL HINTS
If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want to
use for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
what you want.
Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then the interface name on the
setether command line must match the one in /etc/decnet.conf(5).
SEE ALSO
decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)
DECnet utilities March 01 2001 SETETHER(8)