08-18-2012
Amazing! Never had to deal with anything like that, thank goodness.
7 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hi. I am newbie in Unix. I wanted to install Free BSD 5.2.1 to my computer which winXp was already installed. But i couldn't.
I chose Standard. Then it said you are going to use dos style fdisk partitioning. Then a window displayed begining like this.
WARNING: A geometry of 155127/16/63 for... (0 Replies)
Discussion started by: sualcavab
0 Replies
2. Shell Programming and Scripting
Hi,
I have variables like mentioned below and want to separate as mentioned in output.
var1="4 x fibre cards"
var2="2 fibre cards"
var3="6 - fibre cards"
var4="4 x dual-port"
I have variables like this.I want to separate numbers from this and fibre cards from this.
output has to be... (4 Replies)
Discussion started by: ajilesh
4 Replies
3. AIX
Hello,
I have two systems that are being prepared to be SAN attached ..
can anyone tell me any specific checks I should perform prior to the cards being installed...
I am aware of firmware / OS level and relevant drivers, is there anything else?
thanks
Chris. (8 Replies)
Discussion started by: chlawren
8 Replies
4. Solaris
When loooking at files in a directory using ls, how can I tell if I have a hard link or soft link? (11 Replies)
Discussion started by: Harleyrci
11 Replies
5. AIX
Hi
I'm logged in as root in an aix box
Which command will list all the soft links and hard links present in the server ? (2 Replies)
Discussion started by: newtoaixos
2 Replies
6. Hardware
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Discussion started by: atahmass
1 Replies
7. AIX
Hi guys,
I've been trying to tackle this issue for days and I'm stumped. Hopefully someone can give more light on what else I can do.
I have a p7 series box, with dual VIOS and 10 lpars and everything was working fine until I had to move the box to another location in the data centre. Ensured... (16 Replies)
Discussion started by: aixkidbee
16 Replies
LEARN ABOUT OSF1
ntptrace
ntptrace(8) System Manager's Manual ntptrace(8)
NAME
ntptrace - Traces a chain of NTP hosts back to their master time source
SYNOPSIS
/usr/sbin/ntptrace [-dnv] [-r retries] [-t timeout] [server]
OPTIONS
Turns on some debugging output. Turns off the printing of host names; instead, host IP addresses are given. This may be necessary if a
nameserver is down. Sets the number of retransmission attempts for each host; default = 5. Sets the retransmission timeout (in seconds);
default = 2. Prints verbose information about the NTP servers.
DESCRIPTION
The ntptrace command determines where a given Network Time Protocol (NTP) server gets its time from, and follows the chain of NTP servers
back to their master time source. If given no arguments, it starts with localhost.
The following is an example of the output from ntptrace: % ntptrace localhost: stratum 4, offset 0.0019529, synch distance 0.144135
server2.bozo.com: stratum 2, offset 0.0124263, synch distance 0.115784 usndh.edu: stratum 1, offset 0.0019298, synch distance 0.011993,
refid 'WWVB'
On each line, the fields are (left to right): the host name, the host's stratum, the time offset between that host and the local host (as
measured by ntptrace; this is why it is not always zero for localhost), the host's synchronization distance, and (only for stratum-1
servers) the reference clock ID. All times are given in seconds. (Synchronization distance is a measure of the goodness of the clock's
time.)
SEE ALSO
Commands: xntpd(8), xntpdc(8)
ntptrace(8)