08-17-2012
BitLord,
You need to set the IP's in your Global Zone for the particular zone you are trying to configure.
Run the following commands:
# add net
#set address= 192.x.x.x
#set physical=
# end -----> to commit the network configuration. But you will still be within the Zone configuration table okay.
If you run these commands and you are still running into the same problem, my suggestion would be to start over. But this time around add the following commands above before committing the Zone.
Good luck
9 More Discussions You Might Find Interesting
1. Solaris
I have a general question regarding Zone Migration.
I have an older system that is currently running a zone configured with ProFTPD & SSL.
If I want to migrate or clone that zone to another (much newer) system, will I still have to setup & configure ProFTPD & SSL on the new system? (3 Replies)
Discussion started by: em23
3 Replies
2. Solaris
OK I am running solaris 10.
I made some changes to my ipf.conf file and issued the command:
ipf -Fa -f /etc/ipf/ipf.conf
to flush out the old and bring in the new changes.
When I ran ipfstat -ioh to verify it had brought in the new rule set I saw something I wasn't expecting to see.
I... (3 Replies)
Discussion started by: NewSolarisAdmin
3 Replies
3. Solaris
Hi all,
i am new learner in Zoning and virtualization Technology and i have some question's about it
i create zone using this step
zonecfg -z app-apache
create
set zonepath=/zone_adm/app-apache
add net
set address=192.168.1.250
set physical=bge0
end
set autoboot=true
verify
commit... (13 Replies)
Discussion started by: coxmanchester
13 Replies
4. Solaris
I'm trying to enable IPF ( ip filter ) on solaris 10 release 6/06 Solaris 10 6/06 s10s_u2wos_09a SPARC
so i enabled svc:/network/ipfilter:default
it was disabled by default and svc:/network/pfil:default was enabled and online
there only one config file under etc
$/etc/ipf/ipf.conf
i... (1 Reply)
Discussion started by: h@foorsa.biz
1 Replies
5. Cybersecurity
I'm running IPF on solaris 10
bash-3.00# ipf -V #display ipf version
ipf: IP Filter: v4.1.9 (592)
Kernel: IP Filter: v4.1.9
Running: yes
Log Flags: 0 = none set
Default: pass all, Logging: available
Active list: 1
Feature mask: 0x107
with the following rules
bash-3.00# ipfstat -o -i... (0 Replies)
Discussion started by: h@foorsa.biz
0 Replies
6. Solaris
I have two physical servers, with zones that mount local storage.
We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point).
It failed to mount on every boot because the directory existed in the zone.
I... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies
7. UNIX for Advanced & Expert Users
I've been going crazy trying to get this working. Here's the situation: we have a Solaris 10 box that connects an internal network to an external network. We're using ipf/ipnat on it. We've added a couple of new boxes to the internal network (192.168.1.100, .101) and want to be able to get to port... (1 Reply)
Discussion started by: spakov
1 Replies
8. Solaris
I have a question about losing a node in a zone cluster. Hopefully I can explain enough for someone to answer.
Let's say I have a zone cluster spread over 3 physical nodes. If Node1 crashes, would I be correct in assuming I would lose all zones on Node1?
If I lost Node1 below, would I lose... (4 Replies)
Discussion started by: MasonJ
4 Replies
9. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
LEARN ABOUT OPENSOLARIS
dat_pz_free
dat_pz_free(3DAT) Direct Access Transport Library Functions dat_pz_free(3DAT)
NAME
dat_pz_free - destroy an instance of the Protection Zone
SYNOPSIS
cc [ flag... ] file... -ldat [ library... ]
#include <dat/udat.h>
DAT_RETURN
dat_pz_free (
IN DAT_PZ_HANDLE pz_handle
)
PARAMETERS
pz_handle Handle for an instance of Protection Zone to be destroyed.
DESCRIPTION
The dat_pz_free() function destroys an instance of the Protection Zone. The Protection Zone cannot be destroyed if it is in use by an End-
point, LMR, or RMR.
Use of the handle of the destroyed Protection Zone in any subsequent operation except for dat_pz_free() fails.
RETURN VALUES
DAT_SUCCESS The operation was successful.
DAT_INVALID_STATE Parameter in an invalid state. The Protection Zone was in use by Endpoint, LMR, or RMR instances.
DAT_INVALID_HANDLE The pz_handle parameter is invalid.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface Stability |Standard: uDAPL, 1.1, 1.2 |
+-----------------------------+-----------------------------+
|MT-Level |Unsafe |
+-----------------------------+-----------------------------+
SEE ALSO
libdat(3LIB), attributes(5)
SunOS 5.11 16 Jul 2004 dat_pz_free(3DAT)