08-16-2012
Unless I am wrong you have Solaris 11 Express installed, not Solaris 11. As far as I know, Solaris 11 is 64-bit only.
Please show us the contents of your e1000g.conf. I suspect a syntax error.
This User Gave Thanks to fpmurphy For This Post:
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I changed the logrotate.conf file to make a new log file to be automatically rotated daily. But after a night, I have not seen the rotated file.
When does this rotation happen? I mean what is the exact time?
In addition, do I have to restart what deamon to make the change take effect? (10 Replies)
Discussion started by: fredao
10 Replies
2. UNIX for Advanced & Expert Users
HI,
I want a help for Configuring snmpd.conf and snmptrapd.conf (i.e Configuring SNMP)
for receiving
TRAPS in my networks. I am using RHEL4.0 OS.
Please tell me How I can configure above two files in a proper way and at an
advanced level.
Especially I am getting... (2 Replies)
Discussion started by: jagdish.machhi@
2 Replies
3. Red Hat
i have installed rhel5 quite many times.......
when i see grub.conf after installation, somtimes "kernel /boot/vmlinuz-2.6.18-8.el5 ro=LABEL=/ rhgb quiet" will be there or "kernel /boot/vmlinuz-2.6.18-8.el5 ro=LABEL=/1 rhgb quiet" will be there................
what is the significance of label=/... (1 Reply)
Discussion started by: sagar_md
1 Replies
4. UNIX for Dummies Questions & Answers
Hi everyone
A quick question during a audit this was determined to be a security issue
In the resolv.conf there is a “.” At the end of the domain name
Like this
domain mydomain.com.
I which to understand the function or significance of the .
thk (3 Replies)
Discussion started by: Ex-Capsa
3 Replies
5. Red Hat
What would be Redhat RHEL 4.0 equivalent for Solaris sd.conf and lpfc.conf? What are the files called and where are the files located? (1 Reply)
Discussion started by: soupbone38
1 Replies
6. Solaris
Hello Guys,
Do we need to configure this file only if we add SAN disk or even if we add local disk, do we need to modify? (4 Replies)
Discussion started by: mokkan
4 Replies
7. Solaris
Hi all,
I was abit confused where to put this problem, since its only relevant to OI and therefore I put it here.
For the past weeks I was building my own NAS based on OI 151 a7. Everything was sweet, until I bumped into one horrific issue which cause the link between my NAS to my PC... (10 Replies)
Discussion started by: enno
10 Replies
8. Shell Programming and Scripting
Hello all,
Newbie here.
I'm currently tasked with updating rsyslog.conf and auditd.conf on a large set of servers. I know the exact logging configurations that I want to enable. I have updated both files on on a server and hope to use the updated files as a template for the rest of the... (3 Replies)
Discussion started by: Mide
3 Replies
9. Solaris
Hi,
I've installed Solaris 11.3(live media) and configured DNS. Everytime I reboot the server, resolv.conf got deleted and it created a new nsswitch.conf.
I used below to configure both settings:
# svccfg -s dns/client
svc:/network/dns/client> setprop config/nameserver = (xx.xx.xx.aa... (1 Reply)
Discussion started by: flexihopper18
1 Replies
ndd(1M) System Administration Commands ndd(1M)
NAME
ndd - get and set driver configuration parameters
SYNOPSIS
ndd [-set] driver parameter [value]
DESCRIPTION
ndd gets and sets selected configuration parameters in some kernel drivers. Currently, ndd only supports the drivers that implement the
TCP/IP Internet protocol family. Each driver chooses which parameters to make visible using ndd. Since these parameters are usually
tightly coupled to the implementation, they are likely to change from release to release. Some parameters may be read-only.
If the -set option is omitted, ndd queries the named driver, retrieves the value associated with the specified parameter, and prints it. If
the -set option is given, ndd passes value, which must be specified, down to the named driver which assigns it to the named parameter.
By convention, drivers that support ndd also support a special read-only parameter named ``?'' which can be used to list the parameters
supported by the driver.
EXAMPLES
Example 1: Getting Parameters Supported By The TCP Driver
To see which parameters are supported by the TCP driver, use the following command:
example% ndd /dev/tcp ?
The parameter name ``?'' may need to be escaped with a backslash to prevent its being interpreted as a shell meta character.
The following command sets the value of the parameter ip_forwarding in the dual stack IP driver to zero. This disables IPv4 packet forward-
ing.
example% ndd -set /dev/ip ip_forwarding 0
Similarly, in order to disable IPv6 packet forwarding, the value of parameter ip6_forwarding
example% ndd -set /dev/ip ip6_forwarding 0
To view the current IPv4 forwarding table, use the following command:
example% ndd /dev/ip ipv4_ire_status
To view the current IPv6 forwarding table, use the following command:
example% ndd /dev/ip ipv6_ire_status
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
nca(1), ioctl(2), attributes(5), arp(7P), ip(7P), ip6(7P), tcp(7P), udp(7P)
NOTES
The parameters supported by each driver may change from release to release. Like programs that read /dev/kmem, user programs or shell
scripts that execute ndd should be prepared for parameter names to change.
The ioctl() command that ndd uses to communicate with drivers is likely to change in a future release. User programs should avoid making
dependencies on it.
The meanings of many ndd parameters make sense only if you understand how the driver is implemented.
SunOS 5.10 8 Nov 1999 ndd(1M)