Sponsored Content
Full Discussion: Zone ipf question
Operating Systems Solaris Zone ipf question Post 302686487 by bartus11 on Tuesday 14th of August 2012 04:43:40 PM
Old 08-14-2012
What do you mean by "IPs are not shared"? If you have zone with shared network interface, then IP will show up in ifconfig -a output on the global zone as well as in the zone itself.
 

9 More Discussions You Might Find Interesting

1. Solaris

Question regarding Zone Migration

I have a general question regarding Zone Migration. I have an older system that is currently running a zone configured with ProFTPD & SSL. If I want to migrate or clone that zone to another (much newer) system, will I still have to setup & configure ProFTPD & SSL on the new system? (3 Replies)
Discussion started by: em23
3 Replies

2. Solaris

ipf.conf question

OK I am running solaris 10. I made some changes to my ipf.conf file and issued the command: ipf -Fa -f /etc/ipf/ipf.conf to flush out the old and bring in the new changes. When I ran ipfstat -ioh to verify it had brought in the new rule set I saw something I wasn't expecting to see. I... (3 Replies)
Discussion started by: NewSolarisAdmin
3 Replies

3. Solaris

Some Question's about Zone

Hi all, i am new learner in Zoning and virtualization Technology and i have some question's about it i create zone using this step zonecfg -z app-apache create set zonepath=/zone_adm/app-apache add net set address=192.168.1.250 set physical=bge0 end set autoboot=true verify commit... (13 Replies)
Discussion started by: coxmanchester
13 Replies

4. Solaris

IPF on Solaris 10 prior 10 8/07 releases

I'm trying to enable IPF ( ip filter ) on solaris 10 release 6/06 Solaris 10 6/06 s10s_u2wos_09a SPARC so i enabled svc:/network/ipfilter:default it was disabled by default and svc:/network/pfil:default was enabled and online there only one config file under etc $/etc/ipf/ipf.conf i... (1 Reply)
Discussion started by: h@foorsa.biz
1 Replies

5. Cybersecurity

IPF pass in connection to port 21 even with no explicit rule

I'm running IPF on solaris 10 bash-3.00# ipf -V #display ipf version ipf: IP Filter: v4.1.9 (592) Kernel: IP Filter: v4.1.9 Running: yes Log Flags: 0 = none set Default: pass all, Logging: available Active list: 1 Feature mask: 0x107 with the following rules bash-3.00# ipfstat -o -i... (0 Replies)
Discussion started by: h@foorsa.biz
0 Replies

6. Solaris

Zone failes to boot due to mount issue, dir exists in zone.

I have two physical servers, with zones that mount local storage. We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point). It failed to mount on every boot because the directory existed in the zone. I... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies

7. UNIX for Advanced & Expert Users

ipf/ipnat NAT/port forward issues

I've been going crazy trying to get this working. Here's the situation: we have a Solaris 10 box that connects an internal network to an external network. We're using ipf/ipnat on it. We've added a couple of new boxes to the internal network (192.168.1.100, .101) and want to be able to get to port... (1 Reply)
Discussion started by: spakov
1 Replies

8. Solaris

Zone Cluster Question

I have a question about losing a node in a zone cluster. Hopefully I can explain enough for someone to answer. Let's say I have a zone cluster spread over 3 physical nodes. If Node1 crashes, would I be correct in assuming I would lose all zones on Node1? If I lost Node1 below, would I lose... (4 Replies)
Discussion started by: MasonJ
4 Replies

9. UNIX for Advanced & Expert Users

Solaris 10: I forgot to detach a zone before zpool export. Uninstall zone?

Dear all, recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes. I did the following: host1: $ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed $ zpool export zone1 host2: $ zpool... (2 Replies)
Discussion started by: custos
2 Replies
brands(5)						Standards, Environments, and Macros						 brands(5)

NAME
brands - alternate operating environments for non-global zones DESCRIPTION
The branded zone (BrandZ) framework extends the Solaris Zones infrastructure described in zones(5) to include the creation of brands, which provide non-global zones that contain non-native operating environments. The term "brand" can refer to a wide range of operating environments. All brand management is performed as extensions to the current zones structure. Every zone is configured with an associated brand. The brand type is used to determine which scripts are executed when a zone is installed and booted. In addition, a zone's brand is used to properly identify the correct application type at application launch time. The default is the native brand. A branded zone will support exactly one brand of non-native binary, which means that a branded zone provides a single operating environ- ment. Once a zone has been assigned a brand, that brand cannot be changed or removed. BrandZ extends the zones tools in the following ways: o A brand is an attribute of a zone, set at zone create time. o The zonecfg tool (see zonecfg(1M)) is used to set a zone's brand type and configure the zone. o The zoneadm tool (see zoneadm(1M)) is used to report a zone's brand type and administer the zone. Device Support The devices supported by each zone are documented in the man pages and other documentation for that brand. The zones infrastructure detects any attempt to add an unsupported device and issues a warning to the administrator. If the administrator chooses to add an unsupported device despite that warning, that device might or might not work as expected. The configuration will be untested and unsupported. ATTRIBUTES
See attributes(5) for a description of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWzoneu | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
mdb(1), zlogin(1), zonename(1), dtrace(1M), in.rlogind(1M), sshd(1M), zoneadm(1M), zonecfg(1M), kill(2), priocntl(2), getzoneid(3C), ucred_get(3C), getzoneid(3C), proc(4), attributes(5), lx(5), native(5), privileges(5), zones(5), lx_systrace(7D), crgetzoneid(9F) SunOS 5.11 13 Feb 2009 brands(5)
All times are GMT -4. The time now is 10:40 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy