08-10-2012
Do you have any non-ip networks setup in your HACMP configuration? SAN heartbeat and/or Serial network heartbeat?
These would help discern between a true network problem or a node down problem.
10 More Discussions You Might Find Interesting
1. AIX
(0 Replies)
Discussion started by: mhenryj
0 Replies
2. AIX
Hello
I am a noobie to HACMP
I have 2 55A servers and a 7031 disk subsystem
For HACMP to work, do I need to have the hdisks on both servers to match the same drives??
The hdisks on each box are currently different:
hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on... (1 Reply)
Discussion started by: mhenryj
1 Replies
3. HP-UX
Hi,
Can anybody advice whether it is possible to configure HACMP in HP-UX Server.
To my knowledge HACMP is IBM Solution.
Thanks && Regards,
N. Poorna Chandra Rao. (2 Replies)
Discussion started by: npcrao
2 Replies
4. AIX
Hi,
I needed space on a FS, and when I've added the space on the filesystem, I did it trough the regular smitty fs inteface and not with smitty cl_lvm.
Can someone help me to repair the situat before a faileover happen ?
Thanks for your help,:mad: (13 Replies)
Discussion started by: azzed27
13 Replies
5. AIX
Hi,
Can we use network for heartbeat, I mean can we use different network card for heartbeat. (6 Replies)
Discussion started by: vjm
6 Replies
6. AIX
hi
can anyone explain the concepts of HACMP and configuration (step by step) (2 Replies)
Discussion started by: udtyuvaraj
2 Replies
7. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
8. AIX
Hi.
We have a two node HA cluster.
We got a request to change one of the VG name?
Is there an option to do this online ? If it requires downtime can someone please explain me the steps for doing it ?
Let me know if you need any outputs from the servers (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. AIX
Hi,
I have question about HA. I have 2 node cluster (node A and node B). I have configured network and disk HB. If my network is up and i remove both the fc cables from node A will my cluster failover to node B? I have checked and its not working, if i want my cluster to failover in this... (5 Replies)
Discussion started by: powerAIX
5 Replies
10. AIX
hello
ive 2 nodes aix 6100-04-10-1119 with hacmp 6.1.0.0
my qustion is :
can i add default gateway to one member node with hacmp a live or to do take over to realse one of the members ?
thanks
When it is urgent, then open the thread up in the appropriate subforum next time, thanks. (3 Replies)
Discussion started by: ariec
3 Replies
cmruncl(1m) cmruncl(1m)
NAME
cmruncl - run a high availability cluster
SYNOPSIS
cmruncl [-f] [-v] [-n node_name...] [-t | -w none]
DESCRIPTION
cmruncl causes all nodes in a configured cluster or all nodes specified to start their cluster daemons and form a new cluster.
To start a cluster, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the cluster configuration
file. See access policy in cmquerycl(1m).
This command should only be run when the cluster is not active on any of the configured nodes. This command verifies the network configu-
ration before causing the nodes to start their cluster daemons. If a cluster is already running on a subset of the nodes, the cmrunnode
command should be used to start the remaining nodes and force them to join the existing cluster.
If node_name is not specified, the cluster daemons will be started on all the nodes in the cluster. All nodes in the cluster must be
available for the cluster to start unless a subset of nodes is specified.
Options
cmruncl supports the following options:
-f Force cluster startup without warning message and continuation prompt that are printed with the -n option.
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages.
The -w option is not required with the -t option as -t does not validate network connectivity, but assumes that all the
nodes can meet any external dependencies such as EMS resources, package subnets, and storage.
-n node_name...
Start the cluster daemon on the specified subset of node(s).
-w none By default network probing is performed to check that the network connectivity is the same as when the cluster was config-
ured. Any anomalies are reported before the cluster daemons are started. The -w none option disables this probing. The
option should only be used if this network configuration is known to be correct from a recent check.
RETURN VALUE
cmruncl returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Run the cluster daemon:
cmruncl
Run the cluster daemons on node1 and node2:
cmruncl -n node1 -n node2
AUTHOR
cmruncl was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmhaltnode(1m), cmrunnode(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmruncl(1m)