08-07-2012
I'd be surprised if this was possible with software.
If you need accurate ambient figures, get an engineer to use a non-intrusive current meter on each mains lead.
However, beware of start-up current which can be much higher just after you power the computer on. This is why we have a designated power-up sequence (with delays) should there be a power-down of a computer room.
The manufacturer's maximum figures should be on the plate near the mains lead of each component.
8 More Discussions You Might Find Interesting
1. HP-UX
Hi All,
Need to find the power consumption of a RX7640 server.
Please help.
Regards,
Sag. (3 Replies)
Discussion started by: sag71155
3 Replies
2. Programming
Hi,
my C++ program does some memory consuming tasks and runs several minutes.
During execution time, I want to print information on the current memory consumption and peak memory consumption of my program into a logfile.
How can I retrieve this information, i.e. which functions are available... (0 Replies)
Discussion started by: DarthVader77
0 Replies
3. AIX
Hello All,
Can anybody please tell me what is the maximum limit of Physical IBM Power Machine which can be handled by single HMC at a single point of time?
Thanks,
Jenish (1 Reply)
Discussion started by: jenish_shah
1 Replies
4. Solaris
hi friends, we are relocating our DC and need to plan out electrical power for the new DC.
are there ways i could find the actual power consumption from my current servers ? instead of the product specs. (2 Replies)
Discussion started by: Exposure
2 Replies
5. UNIX Desktop Questions & Answers
Hi All
I am new to UNIX ,can any one please help in finding MEMORY CONSUMPTION of VLC when i use it as Streaming Server.
I need to log the memory consumption for atleast 10 hours.
Can any one help me in finding this Please (1 Reply)
Discussion started by: ravikanth17
1 Replies
6. AIX
Hi,
This thread has been posted before on linuxquestions.org, but no answer, maybe because this is unix question and not linux. I'm posting the same thread here, hope I can get an answer from someone in the meantime, I wish I could post of emergency thread but it needs bits which I don't have :... (6 Replies)
Discussion started by: aLuViAn
6 Replies
7. AIX
Hi,
I have installed the HMC on the VMWare VM. I try to add the power machine (managed system) and asking for a password? So this is the IBM predefined password of Power Machine?
In the VMWare perspective, we can login to ESX host to do some management tasks. But how about the Power machine?... (6 Replies)
Discussion started by: Phat
6 Replies
8. AIX
Hello,
I would like to check how many SAS disks and its size per disk for the whole power system. As per my understanding, if we assign the SAS controller to LPAR, then we can see the disk in lpar smitty command.
How can we check from the Power machine(physical ones) as well? I think the... (5 Replies)
Discussion started by: Phat
5 Replies
LEARN ABOUT CENTOS
reboot
HALT(8) halt HALT(8)
NAME
halt, poweroff, reboot - Halt, power-off or reboot the machine
SYNOPSIS
halt [OPTIONS...]
poweroff [OPTIONS...]
reboot [OPTIONS...]
DESCRIPTION
halt, poweroff, reboot may be used to halt, power-off or reboot the machine.
OPTIONS
The following options are understood:
--help
Prints a short help text and exits.
--halt
Halt the machine, regardless of which one of the three commands is invoked.
-p, --poweroff
Power-off the machine, regardless of which one of the three commands is invoked.
--reboot
Reboot the machine, regardless of which one of the three commands is invoked.
-f, --force
Force immediate halt, power-off, reboot. Do not contact the init system.
-w, --wtmp-only
Only write wtmp shutdown entry, do not actually halt, power-off, reboot.
-d, --no-wtmp
Do not write wtmp shutdown entry.
--no-wall
Do not send wall message before halt, power-off, reboot.
EXIT STATUS
On success, 0 is returned, a non-zero failure code otherwise.
NOTES
These are legacy commands available for compatibility only.
SEE ALSO
systemd(1), systemctl(1), shutdown(8), wall(1)
systemd 208 HALT(8)