08-03-2012
I have read the documents, the confusion arising if whether the hardware supports or not,
as you mentioned that I need to download the driver
devices.pci.1410be02 device driver package
i will install and check and post here if it solves the problem. But my main concern is that does the hardware support or not ?
10 More Discussions You Might Find Interesting
1. SCO
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies
2. Solaris
hi
this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network)
i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Discussion started by: Landser
4 Replies
3. Solaris
Dear Friends,
I need to configure T5240 with Internal SAS RAID HBA(SG-XPCIESAS-R-INT-Z).. T5240 uses 8 hard disks... From the documents of RAID card I have found that I need to create a jump start server to include three packages SUNWaac, StorMan, SUNWgccruntime if Im using solaris10 5/08...
... (5 Replies)
Discussion started by: nicktrix
5 Replies
4. Red Hat
I am planning on building a fedora box with raid controller (database server).
Is anybody done that ? also what kind of software do you need to backup and recover data. (1 Reply)
Discussion started by: amir07
1 Replies
5. Hardware
Hi,
We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks.
This also has an External Raid Controller (Storagetek Eight-Port, External HBA
Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk.
... (1 Reply)
Discussion started by: ranjansukumar
1 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
8. Red Hat
Hello,
I am using Red Hat 2.6.23.1 with RAID 6 controller (card).
(When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.)
I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Discussion started by: Dbugy
7 Replies
9. SCO
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Discussion started by: thm2222
7 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT FREEBSD
snd_atiixp
SND_ATIIXP(4) BSD Kernel Interfaces Manual SND_ATIIXP(4)
NAME
snd_atiixp -- ATI IXP bridge device driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device sound
device snd_atiixp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
snd_atiixp_load="YES"
DESCRIPTION
The snd_atiixp bridge driver allows the generic audio driver, sound(4), to attach to ATI IXP audio devices. This driver supports 16bit play-
back and recording, and 32bit native playback and recording.
Runtime Configuration
The following sysctl(8) variables are available in addition to those available to all sound(4) devices:
dev.pcm.%d.polling Experimental polling mode, where the driver operates by querying the device state on each tick using callout(9).
Polling is disabled by default. Do not enable it unless you are facing weird interrupt problems or if the device
cannot generate interrupts at all.
HARDWARE
The snd_atiixp driver supports the following audio chipsets:
o ATI IXP 200
o ATI IXP 300
o ATI IXP 400
SEE ALSO
sound(4)
HISTORY
The snd_atiixp device driver first appeared in FreeBSD 6.1.
AUTHORS
This manual page was written by Joel Dahl <joel@FreeBSD.org>.
BUGS
The snd_atiixp driver does not support S/PDIF, but implementing it should be fairly easy if the right hardware is available.
32bit native recording is broken on some hardware.
BSD
November 29, 2006 BSD