All,
I see that there are 2 nic card available . How can I know all the details about these 2 nic cards.
-rw-r--r-- 1 root root 10 Apr 16 15:00 hostname.bge0
-rw-r--r-- 1 root other 17 Apr 22 08:56 hostname.bge2
please let me know
thanks
-prasad (4 Replies)
I do a ssh to remote host(A1) from local host(L1). I then ssh to another remote(A2) from A1.
When I do a who -m from A2, I see the "connected from" as "A1".
=> who -m
userid pts/2 2010-03-27 08:47 (A1)
I want to identify who is the local host who initiated the connection to... (3 Replies)
Greetings Forumers!
I am running into an issue with multiple zones on an M5000 with 2 NICs. The NICs are on separate VLANs. These zones are using the 2 NICs to communicate with other systems but when they need to communicate with a zone on the same system, but different NIC, the application... (9 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I have a Sun Blade 2500 with SUN 5.9 OS installed. I have one NIC built-in which is working fine.
I insert another new NIC in the machine with four RJ45 connector options(means four NICs in one Card). The problem is i am not able to see the new NIC
Thanks (13 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Dear,
I hope you all will be ok.
I have an issue with Solaris box running on x86 Blade.
I am unable to ping a node neither traceroute. I am able to do traceroute from oce0:6 port which have IP and subnet of same type which oce0:1 has.
details are as follows:
Problem:
root@rinams02:/#... (3 Replies)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT MOJAVE
talk
TALK(1) BSD General Commands Manual TALK(1)NAME
talk -- talk to another user
SYNOPSIS
talk person [ttyname]
DESCRIPTION
The talk utility is a visual communication program which copies lines from your terminal to that of another user.
Options available:
person If you wish to talk to someone on your own machine, then person is just the person's login name. If you wish to talk to a user on
another host, then person is of the form 'user@host' or 'host!user' or 'host:user'.
ttyname If you wish to talk to a user who is logged in more than once, the ttyname argument may be used to indicate the appropriate terminal
name, where ttyname is of the form 'ttyXX'.
When first called, talk sends the message
Message from TalkDaemon@his_machine...
talk: connection requested by your_name@your_machine.
talk: respond with: talk your_name@your_machine
to the user you wish to talk to. At this point, the recipient of the message should reply by typing
talk your_name@your_machine
It does not matter from which machine the recipient replies, as long as his login-name is the same. Once communication is established, the
two parties may type simultaneously, with their output appearing in separate windows. Typing control-L '^L' will cause the screen to be
reprinted. Typing control-D '^D' will clear both parts of your screen to be cleared, while the control-D character will be sent to the
remote side (and just displayed by this talk client). Your erase, kill, and word kill characters will behave normally. To exit, just type
your interrupt character; talk then moves the cursor to the bottom of the screen and restores the terminal to its previous state.
Permission to talk may be denied or granted by use of the mesg(1) command. At the outset talking is allowed.
CONFIGURATION
The talk utility relies on the talkd system daemon. See talkd(8) for information about enabling talkd.
FILES
/etc/hosts to find the recipient's machine
/var/run/utmpx to find the recipient's tty
SEE ALSO mail(1), mesg(1), wall(1), who(1), write(1), talkd(8)HISTORY
The talk command appeared in 4.2BSD.
In FreeBSD 5.3, the default behaviour of talk was changed to treat local-to-local talk requests as originating and terminating at localhost.
Before this change, it was required that the hostname (as per gethostname(3)) resolved to a valid IPv4 address (via gethostbyname(3)), making
talk unsuitable for use in configurations where talkd(8) was bound to the loopback interface (normally for security reasons).
BUGS
The version of talk released with 4.3BSD uses a protocol that is incompatible with the protocol used in the version released with 4.2BSD.
Multibyte characters are not recognized.
BSD August 21, 2008 BSD