07-31-2012
anyone faced similar problem or know how to solve this problem ?
what feature code I should be looking for RAID Adapter ?
10 More Discussions You Might Find Interesting
1. SCO
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies
2. Solaris
hi
this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network)
i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Discussion started by: Landser
4 Replies
3. Solaris
Dear Friends,
I need to configure T5240 with Internal SAS RAID HBA(SG-XPCIESAS-R-INT-Z).. T5240 uses 8 hard disks... From the documents of RAID card I have found that I need to create a jump start server to include three packages SUNWaac, StorMan, SUNWgccruntime if Im using solaris10 5/08...
... (5 Replies)
Discussion started by: nicktrix
5 Replies
4. Red Hat
I am planning on building a fedora box with raid controller (database server).
Is anybody done that ? also what kind of software do you need to backup and recover data. (1 Reply)
Discussion started by: amir07
1 Replies
5. Hardware
Hi,
We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks.
This also has an External Raid Controller (Storagetek Eight-Port, External HBA
Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk.
... (1 Reply)
Discussion started by: ranjansukumar
1 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
8. Red Hat
Hello,
I am using Red Hat 2.6.23.1 with RAID 6 controller (card).
(When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.)
I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Discussion started by: Dbugy
7 Replies
9. SCO
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Discussion started by: thm2222
7 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT DEBIAN
raidfile-config
RAIDFILE-CONFIG(8) Box Backup RAIDFILE-CONFIG(8)
NAME
raidfile-config - Configure Box Backup's RAID files
SYNOPSIS
raidfile-config config-dir blocksize dir1 [dir2 [dir3]]
DESCRIPTION
raidfile-config creates a raidfile.conf file for Box Backup. This file holds information about the directories used to store backups in.
Box Backup supports userland RAID, in a restricted RAID5 configuration, where 3 and only 3 'drives' are supported. You can read more about
RAID5 (and other RAID-levels) here[1].
Parameters
The parameters are as follows:
config-dir
The directory path where configuration files are located. Usually this is /etc/box. raidfile.conf will be written in this directory.
blocksize
The block size used for file storage in the system, in bytes. Using a multiple of the file system block size is a good strategy.
Depending on the size of the files you will be backing up, this multiple varies. Of course it also depends on the native block size of
your file system.
dir1
The first directory in the built-in RAID array.
dir2
The second directory in the built-in RAID array. If you are not using the built-in RAID functionality, this field should be ignored.
You should not use the built-in RAID if you have a hardware RAID solution or if you're using another type of software RAID (like md on
Linux).
dir3
The third directory in the built-in RAID array. The same notes that apply to dir2 also apply to dir3.
Note that there are currently no way to add multiple disk sets to the raidfile.conf file using command line tools, etc. See
raidfile.conf(5) for details on adding more disks.
BUGS
If you find a bug in Box Backup, and you want to let us know about it, join the mailing list[2], and send a description of the problem
there.
To report a bug, give us at least the following information:
o The version of Box Backup you are running
o The platform you are running on (hardware and OS), for both client and server.
o If possible attach your config files (bbstored.conf, bbackupd.conf) to the bug report.
o Also attach any log file output that helps shed light on the problem you are seeing.
o And last but certainly not least, a description of what you are seeing, in as much detail as possible.
FILES
raidfile-config generates the raidfile.conf(5) file.
SEE ALSO
bbstored-config(8), bbstored.conf(5), raidfile.conf(5)
AUTHORS
Ben Summers
Per Thomsen
James O'Gorman
NOTES
1. here
http://en.wikipedia.org/wiki/Redundant_array_of_independent_disks#RAID_5
2. mailing list
http://lists.warhead.org.uk/mailman/listinfo/boxbackup
Box Backup 0.11 10/28/2011 RAIDFILE-CONFIG(8)