Hello All,
Here is a problem of NOHUP.
I am trying to run a process which needs to be up and running even if the session is closed. I tried running it with "nohup", but starngely it is not working, when i exit from the session the process is also getting killed?
plz help me in finding out... (4 Replies)
Hi All,
I have requirement. I am running a job every 30mins. before starting the process, i need to check the process, if the process is still running then i need not trigger the process again, if it is not running then trigger the process again. I am using cron to trigger the shell script. Can... (7 Replies)
Hi
I have a script, which i ran in background, can someone please help in stopping this.
i gave this command:
ksh abc.ksh &
this script sends me a mail every 30 seconds. i have deleted the script but still i am getting the mails. can some one please help me stopping dese.
... (3 Replies)
Hi all,
I wrote a scirpt (abc.sh) in which I defined a loop with an interval equal to 1 hour. I want this script continue to run when I close the terminal, so I ran the following command,
(in the proper directory)
nohup abc.sh
However the script doesn't just keep running when I... (1 Reply)
Hello,
I am trying to find a way to send several sequential commands via SSH to a remote box in a single command.
Thoughts so far:
1) Can I put them into a function and call the function within the ssh command?
e.g.
ssh <targetserver> $(functionx)
No - then it calls the function in... (4 Replies)
Hi All,
Can someone help me in knowing the exact difference between nohup and &.
The definition is quite clear but i only want to know if i run my job using & and in between i hung up my terminal. (10 Replies)
I have a question.
I will be running a background process using nohup and & command at end. I want to send output to a file say myprocess.out.
So will this command work?
nohup myprocess.ksh > myprocess.out &
Thanks in advance guys !!!
:) (3 Replies)
Hello,
I am trying to make a bash script, I tested nohup but it did not help me.
My code is:
ffmpeg -i $input_url -c:v copy -c:a copy -listen 1 -f mpegts http://localhost:port/live/test
When I open it in VLC, it starts feeding my screen and I see bitrate values.
When I stop watching it,... (4 Replies)
Discussion started by: baris35
4 Replies
LEARN ABOUT NETBSD
nohup
NOHUP(1) BSD General Commands Manual NOHUP(1)NAME
nohup -- invoke a command immune to hangups
SYNOPSIS
nohup utility [arg ...]
DESCRIPTION
The nohup command allows the specified utility to be protected from termination if the user should become logged out (for example, due to a
modem line or TCP/IP connection being dropped). To do this, nohup sets the SIGHUP signal(3) (``terminal line hangup'') to be ignored, then
executes utility along with any arguments.
If the standard output is a terminal, the standard output is appended to the file nohup.out in the current directory. If standard error is a
terminal, it is directed to the same place as the standard output. If the output file nohup.out cannot be created in the current directory,
nohup attempts to create the file in the user's home directory. If the file nohup.out cannot be created, either in the current directory or
the user's home directory, nohup will exit without invoking utility, with an exit value as described below.
ENVIRONMENT
The following variable is used by nohup.
HOME User's home directory.
EXIT STATUS
The nohup utility exits with one of the following values:
126 The utility was found but could not be invoked.
127 The utility could not be found or an error occurred in nohup.
Otherwise, the exit status of nohup will be that of utility.
SEE ALSO signal(3)STANDARDS
The nohup command is expected to be IEEE Std 1003.2 (``POSIX.2'') compatible.
BSD July 15, 2005 BSD