After I rebooted I get IPv6 back, what's bad that when I tried to create an IPMP by issuing ipadm command, it created two ipmp for me, one is v4 and v6.
Code:
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=9040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER> mtu 1500 index 2
inet 192.168.0.223 netmask ffffff00 broadcast 192.168.0.255
groupname ipmp0
ether 0:21:28:f9:9d:e8
net1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 4
inet 0.0.0.0 netmask ff000000
groupname ipmp0
ether 0:21:28:f9:9d:e9
net4: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 169.254.182.77 netmask ffffff00 broadcast 169.254.182.255
ether 2:21:28:57:47:17
ipmp0: flags=8001004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4,IPMP> mtu 1500 index 5
inet 192.168.0.157 netmask ffffff00 broadcast 192.168.0.255
groupname ipmp0
net4: flags=20002000840<RUNNING,MULTICAST,IPv6> mtu 1500 index 3
inet6 ::/0
ether 2:21:28:57:47:17
ipmp0: flags=28002000840<RUNNING,MULTICAST,IPv6,IPMP> mtu 1280 index 5
inet6 ::/0
groupname ipmp0
Hi! I have to configure ipv6 network between two computers with Solaris 10 but I not an expert in using any unix system and I do it becouse I need it to my study. Is someone here who could help me and describe step-by-step how to do it? please!!!
PS. I need to configure network to do secure... (1 Reply)
Hi, anyone has had experience in a static setting an IPv6 interface?, I'm trying accordance with the admin guide (ipv6 network configuration tasks), configure one interface in the server, actually i can do ping to my default gateway and access the Internet in IPv6, the specific point is however,... (3 Replies)
Guide on how to disable ipv6 for Centos and RedHat
1) Edit /etc/sysconfig/network-scripts/ifcfg-eth0 and change:
NETWORKING_IPV6=yes to NETWORKING_IPV6=no
2) Edit /etc/modprobe.conf and add these lines:
alias net-pf-10 off
alias ipv6 off
3) Stop the ipv6tables service:
... (0 Replies)
I have Bind running on a Solaris box that is our main public DNS. Given my very limited knowledge on DNS, I changed a few of the zones in the DNS to be 'dual-stack'. I did it through Webmin, but I know that I can also do it by adding an AAAA-record to the zone file.
My question is how can I make... (2 Replies)
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Hello Dears ,
please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface .
Thanks in... (1 Reply)
Discussion started by: ttashman
1 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO vconfig(8)interfaces(5)vlan September 30 2007 VLAN-INTERFACES(5)