recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
hi
this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network)
i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Dear Friends,
I need to configure T5240 with Internal SAS RAID HBA(SG-XPCIESAS-R-INT-Z).. T5240 uses 8 hard disks... From the documents of RAID card I have found that I need to create a jump start server to include three packages SUNWaac, StorMan, SUNWgccruntime if Im using solaris10 5/08...
... (5 Replies)
I am planning on building a fedora box with raid controller (database server).
Is anybody done that ? also what kind of software do you need to backup and recover data. (1 Reply)
Hi,
We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks.
This also has an External Raid Controller (Storagetek Eight-Port, External HBA
Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk.
... (1 Reply)
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Hello,
I am using Red Hat 2.6.23.1 with RAID 6 controller (card).
(When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.)
I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT FREEBSD
asr
ASR(4) BSD Kernel Interfaces Manual ASR(4)NAME
asr -- driver for Adaptec I2O based SCSI/ATA host bus adapters
SYNOPSIS
device asr
DESCRIPTION
The Adaptec asr driver provides access to disks and disk arrays controlled by I2O based host bus adapters and SmartRAID SCSI RAID adapters
through the standard SCSI disk da(4) interface.
The supported adapters provide 64 bit PCI, Compact PCI, Zero Channel PCI, and up to four channels of Ultra2, Ultra 160, or Ultra320 SCSI, or
two channels of 1GB Fibre. All support RAID-0, RAID-1, RAID-10, RAID-5 and RAID-50 arrays. All SCSI target types are supported. For the
ATA based controllers, one IDE drive per channel is supported. Hot-swapping of IDE drives is not supported at this time.
All host bus adapters must be configured before they can be used with any operating system. Please contact Adaptec directly to obtain the
latest information on configuration utilities for the adapters. Currently there are both a Motif based GUI configuration utility and a CLI
based configuration utility available from the Adaptec Web site. The cards and arrays can also be configured via the BIOS based configura-
tion tool (SMOR).
HARDWARE
The adapters currently supported by the asr driver include the following:
o Adaptec Zero-Channel SCSI RAID 2000S, 2005S, 2010S, 2015S
o Adaptec SCSI RAID 2100S, 2110S
o Adaptec ATA-100 RAID 2400A
o Adaptec SCSI RAID 3200S, 3210S
o Adaptec SCSI RAID 3400S, 3410S
o Adaptec SmartRAID PM1554
o Adaptec SmartRAID PM1564
o Adaptec SmartRAID PM2554
o Adaptec SmartRAID PM2564
o Adaptec SmartRAID PM2664
o Adaptec SmartRAID PM2754
o Adaptec SmartRAID PM2865
o Adaptec SmartRAID PM3754
o Adaptec SmartRAID PM3755U2B / SmartRAID V Millennium
o Adaptec SmartRAID PM3757
o DEC KZPCC-AC (LVD 1-ch, 4MB or 16MB cache), DEC KZPCC-CE (LVD 3-ch, 64MB cache), DEC KZPCC-XC (LVD 1-ch, 16MB cache), DEC KZPCC-XE (LVD
3-ch, 64MB cache) -- rebadged SmartRAID V Millennium
FILES
/dev/asr* Adaptec SCSI RAID control nodes
NOTES
The ATA based controllers present their devices as SCSI-like devices via CAM. For IDE drives attached to these cards, a subset of standard
SCSI commands and mode pages are understood via translation performed in the card's firmware.
SEE ALSO da(4)HISTORY
The asr (Adaptec SCSI RAID) driver first appeared as the dpti2o driver under BSDi BSD/OS 3.2, then under FreeBSD 2.2.8 and was ported over to
the CAM layer represented in 4.0.
AUTHORS
The asr driver was kindly donated by Adaptec and is maintained by Mark Salyzyn <mark_salyzyn@adaptec.com>. This manual page was written by
Mark Salyzyn and fixed up by Jeroen Ruigrok van der Werven <asmodai@FreeBSD.org>.
BSD July 14, 2004 BSD