Hello everybody,
:confused:
I have to change the system disk on an old PC running SCO 5.0.5.
The disk is up and running, this is a preventive action.
My experience on UNIX is very limited and I look for the easyest solution to clone this unit.
Is it possible with commands or through a clone... (2 Replies)
I am using ufsdump and ufsrestore to clone the root disk on one of my servers. I would like to automate this as much as possible, but have run into a problem where it prompts for changing the owner/mode when it is complete.
Any ideas for running this in the background and not being prompted?
... (4 Replies)
Hello guys!
I use the Solaris 10 x86 machine.
I need to clone the boot disk.
Why, when I copy slice 1 - there is a following:
# ufsdump 0f - /dev/rdsk/c0d0s1 | (cd /mnt && ufsrestore rf - )
DUMP: Warning - super-block on device `/dev/rdsk/c0d01` is corrupt - run fsck
Dump: The Entire... (6 Replies)
Hi,
I'm running Ubuntu on my laptop. To keep my data safe and easy disaster recovery as well I bought similar HDD to one installed in my laptop with higher capacity and using USB box I'm doing disk clone to it. So at any time I can replace disk and carry on with my work as before.
I'm trying... (2 Replies)
Hello Friends,
Am in requirement to clone a Live HP-UX server here's details
OS: HpUX B-11.11 with mirrored LVM disks .
S/ws: Remedy, XML engine, Annoysystem, Oracle
All Oracle, XMl and Remedy data is on SAM LUN which is used for clustering .
My requirement to create a clone server and... (10 Replies)
Dear All
I needed to clone my disk to another hard drive . I did it as the following :
#dd if=/dev/sdb of=/dev/sdc
But after a while, the procedure ended with the "writing to /dev/sdc
input/output error" message.
Can you please let me know how can I overcome this as the fdisk now returns as "... (1 Reply)
Discussion started by: hadimotamedi
1 Replies
LEARN ABOUT MINIX
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [ -a blkno [blkno...]] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option
cannot be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 addbadsec(1M)