07-26-2012
If you can ping the IP address with the device powered off, you have a duplicate IP address on the network.
9 More Discussions You Might Find Interesting
1. Solaris
I have a Sun Sparc T2000 (Solaris 10 05-08) and have installed a PCI-X 4GB Single Port HBA card in it.
I have one StorageTek 2540 array that I would like to connect to the T2000.
For the moment it would be a single path connection, but I've ordered a 2nd HBA, so eventually it would be... (4 Replies)
Discussion started by: soliberus
4 Replies
2. Solaris
We're moving our production 3510FC to development, so we need to replace the production 3510FC. The 6140 is nice, but pricey.
Here's the question: Would two 2540's (RAID 10) be 'faster' than one 3510? (RAID 10) and faster than one 6140 (RAID 10)?
One StoregeTek 6140 (16x72GB 15k rpm fc-al... (12 Replies)
Discussion started by: buddhavelvet
12 Replies
3. Filesystems, Disks and Memory
Hi,
We have 12x1TB SATA disks in our array and I need to create 10TB volume. I defined new storage profile on array and when I tried to add volume, I faced with ~2TB limit for new volumes. I didn't find how to set another limit on my storage profile. Is there is a way to configure one large... (3 Replies)
Discussion started by: Sapfeer
3 Replies
4. Solaris
Hi,
I have a simple question on how to correctly disable the matrix?
Looking for the Common Array Manager and I do not see this option...
Thank for help (3 Replies)
Discussion started by: bieszczaders
3 Replies
5. Solaris
Hi peeps,
Was wondering if anyone can help me, got a couple of storagetek 2540's that I need to configure. Trouble is I think they were brought as second user as all that came with them was cables.
Does anyone know how to configure them (i.e. create raid sets and map to Luns and present... (1 Reply)
Discussion started by: callmebob
1 Replies
6. Hardware
Hello all !
I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server.
I... (2 Replies)
Discussion started by: acorradi
2 Replies
7. Hardware
Hi all,
My Sun StorageTek 2540 have redundant batteries, but a battery was failed.
# /opt/SUNWstkcam/bin/sscs list -d MyStorage1 fru
Name FRU Alarm State Status Revision Unique Id
-------------------------- ----------- --------... (2 Replies)
Discussion started by: buyantugs
2 Replies
8. Solaris
Bought a Sun StorageTek 2540 SAN array a few years ago from a company that was going out of business. When we first set it up, we were able to get all the software (Common Array Manager) and firmware directly from Sun.
We just upgraded the drives, but the array is too large for the firmware. Now... (6 Replies)
Discussion started by: edison303
6 Replies
9. Solaris
Hi Guys,
I have situation here ...
server M4000 server lost connectivity to storagetek 2540
, storagetek 2540 unable to be ping.From DAS URL the storage is undetected.
Any idea why this is happening. Please share.
Thank you.
Raj (1 Reply)
Discussion started by: muralirajah
1 Replies
LEARN ABOUT DEBIAN
ipmiping
IPMIPING(8) System Commands IPMIPING(8)
NAME
ipmiping - send IPMI Get Authentication Capabilitiy request to network hosts
SYNOPSIS
ipmiping [OPTION...] destination
DESCRIPTION
ipmiping uses the IPMI Get Channel Authentication Capabilities request datagram to elicit an IPMI Get Channel Authentication Capabilitiesl
response from a remote host. The utility can be used to verify if a remote host supports IPMI. The initial starting sequence number will be
randomized. ipmiping will return 0 to the environment if it receives atleast 1 response from the remote host. Otherwise, it exists with a
value of 1.
OPTIONS
The following options are available
-h Output help menu.
-V Output version.
-c count
Stop after sending count packets.
-i interval
Wait interval seconds between sending each packet. The default is to wait for one second between each packet.
-I interface address
Set source address to specified interface address. Argument may be numeric IP address or name of device.
-t timeout
Time to wait for a response, in seconds. Default is five seconds.
-v Verbose output.
-s num Specify an initial starting sequence number. The default is to use a random initial sequence number.
-d Turn on debugging.
-r version
Specify IPMI version. Available options are "1.5" and "2.0". Default is to use "1.5". Note that packets will always be sent with the
IPMI 1.5 protocol, but IPMI 1.5 vs IPMI 2.0 relevant fields will be communicated in the Get Channel Authentication Capabilities
datagram depending on user choice.
KNOWN ISSUES
It has been observed that some remote BMCs can get "confused" and delay packet responses if duplicate packets (with duplicate sequence num-
bers) are sent in succession very quickly. There is no known way to cleanly deal with a "confused" BMC other than the wait awhile.
Unlike ping(8), local network devicess (e.g. 127.0.0.1) cannot be "pinged".
REPORTING BUGS
Report bugs to <freeipmi-users@gnu.org> or <freeipmi-devel@gnu.org>.
COPYRIGHT
Copyright (C) 2007-2012 Lawrence Livermore National Security, LLC.
Copyright (C) 2003-2007 The Regents of the University of California.
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 3 of the License, or (at your option) any later version.
ORIGIN
Command and manpage based off ping(8).
SEE ALSO
freeipmi(7), ping(8), rmcpping(8)
http://www.gnu.org/software/freeipmi/
ipmiping 1.1.5 2012-06-15 IPMIPING(8)