07-26-2012
Sun 2540 problem
Do you have or have access to the PS2 6-pin DIN to RJ-45 Cable? This will enable you to get a clear and in-depth view of the problem, basically it's the serial diag cable that connects the controller to either a dumb terminal or terminal emulator.
9 More Discussions You Might Find Interesting
1. Solaris
I have a Sun Sparc T2000 (Solaris 10 05-08) and have installed a PCI-X 4GB Single Port HBA card in it.
I have one StorageTek 2540 array that I would like to connect to the T2000.
For the moment it would be a single path connection, but I've ordered a 2nd HBA, so eventually it would be... (4 Replies)
Discussion started by: soliberus
4 Replies
2. Solaris
We're moving our production 3510FC to development, so we need to replace the production 3510FC. The 6140 is nice, but pricey.
Here's the question: Would two 2540's (RAID 10) be 'faster' than one 3510? (RAID 10) and faster than one 6140 (RAID 10)?
One StoregeTek 6140 (16x72GB 15k rpm fc-al... (12 Replies)
Discussion started by: buddhavelvet
12 Replies
3. Filesystems, Disks and Memory
Hi,
We have 12x1TB SATA disks in our array and I need to create 10TB volume. I defined new storage profile on array and when I tried to add volume, I faced with ~2TB limit for new volumes. I didn't find how to set another limit on my storage profile. Is there is a way to configure one large... (3 Replies)
Discussion started by: Sapfeer
3 Replies
4. Solaris
Hi,
I have a simple question on how to correctly disable the matrix?
Looking for the Common Array Manager and I do not see this option...
Thank for help (3 Replies)
Discussion started by: bieszczaders
3 Replies
5. Solaris
Hi peeps,
Was wondering if anyone can help me, got a couple of storagetek 2540's that I need to configure. Trouble is I think they were brought as second user as all that came with them was cables.
Does anyone know how to configure them (i.e. create raid sets and map to Luns and present... (1 Reply)
Discussion started by: callmebob
1 Replies
6. Hardware
Hello all !
I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server.
I... (2 Replies)
Discussion started by: acorradi
2 Replies
7. Hardware
Hi all,
My Sun StorageTek 2540 have redundant batteries, but a battery was failed.
# /opt/SUNWstkcam/bin/sscs list -d MyStorage1 fru
Name FRU Alarm State Status Revision Unique Id
-------------------------- ----------- --------... (2 Replies)
Discussion started by: buyantugs
2 Replies
8. Solaris
Bought a Sun StorageTek 2540 SAN array a few years ago from a company that was going out of business. When we first set it up, we were able to get all the software (Common Array Manager) and firmware directly from Sun.
We just upgraded the drives, but the array is too large for the firmware. Now... (6 Replies)
Discussion started by: edison303
6 Replies
9. Solaris
Hi Guys,
I have situation here ...
server M4000 server lost connectivity to storagetek 2540
, storagetek 2540 unable to be ping.From DAS URL the storage is undetected.
Any idea why this is happening. Please share.
Thank you.
Raj (1 Reply)
Discussion started by: muralirajah
1 Replies
LEARN ABOUT DEBIAN
rds-ping
RDS-PING(1) BSD General Commands Manual RDS-PING(1)
NAME
rds-ping -- test reachability of remote node over RDS
SYNOPSIS
rds-ping [-c count] [-i interval] [-I local_addr] remote_addr
DESCRIPTION
rds-ping is used to test whether a remote node is reachable over RDS. Its interface is designed to operate pretty much the standard ping(8)
utility, even though the way it works is pretty different.
rds-ping opens several RDS sockets and sends packets to port 0 on the indicated host. This is a special port number to which no socket is
bound; instead, the kernel processes incoming packets and responds to them.
OPTIONS
The following options are available for use on the command line:
-c count
Causes rds-ping to exit after sending (and receiving) the specified number of packets.
-I address
By default, rds-ping will pick the local source address for the RDS socket based on routing information for the destination address
(i.e. if packets to the given destination would be routed through interface ib0, then it will use the IP address of ib0 as source
address). Using the -I option, you can override this choice.
-i timeout
By default, rds-ping will wait for one second between sending packets. Use this option to specified a different interval. The timeout
value is given in seconds, and can be a floating point number. Optionally, append msec or usec to specify a timeout in milliseconds
or microseconds, respectively.
Specifying a timeout considerably smaller than the packet round-trip time will produce unexpected results.
AUTHORS
rds-ping was written by Olaf Kirch <olaf.kirch@oracle.com>.
SEE ALSO
rds(7), rds-info(1), rds-stress(1).
BSD
Apr 22, 2008 BSD