07-24-2012
Network card module installation
Hi,
I am using Red Hat 9.0 and it does not have the inbuilt driver module for my onboard lan card (RTL 8169). I downloaded the module (file - r8169-6.017.00.tar.bz2 and even r8169-6.015.00.tar.bz2), but when try to install it it says r8169.h , r8169_n.c , Makefile etc are not ELF formats.
After downlaoding , I did
Make clean modules - Multiple errors
Make install - multiple errors
depmod -a etc. - Files are not valid ELF format
I have checked lspci and my card is shown there with No driver installed.
Module (after extracting ) contains Makefile, Makefile_2.4.x , r8169.h, r8169_n.c, readme. I tried to build the source with its Makefile which also gives multiple errors saying that the parameters in Makefile not found.
Help me out of this !!!
Thanks,
Dexter
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. Solaris
hello solaris friends,
I've tried installing Sun Solaris 10.0, but everytime it seems to bypass the network config. screen that looks similar to this...here's the url:
http://www.hup.hu/old/images/hup/Solaris/Sol10beta7/9.png
I'm able to install it all the way through but I get no... (2 Replies)
Discussion started by: cadmiumgreen
2 Replies
3. UNIX for Advanced & Expert Users
Hi,
I am trying to install perl modules in HPUX under my account. I do not have the root permission.
The module name I am trying to install is Spreadsheet-WriteExcel. I have downloaded the tar.gz file from CPAN and extracted the same under my home directory.
When I try do 'perl... (2 Replies)
Discussion started by: sabyasm
2 Replies
4. Shell Programming and Scripting
Hi All,
I am failry new to Perl.I am trying to install a Perl module (Filesys::df.pm) in an IBM AIX5.3 server.But I could not succeed in that.I am getting the following error:
abcd3dev# make
cc_r -c -D_ALL_SOURCE -D_ANSI_C_SOURCE -D_POSIX_SOURCE -qmaxmem=16384 -qnoansialias... (6 Replies)
Discussion started by: surjithss
6 Replies
5. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
6. Solaris
I have installed Solaris 10 in my PC successfully and my system having Intel(R) PRO/100 VE ethernet card. Solaris OS not able to detect the network card. So i checked the driver (INTCGigaE) and reinstalled. Still network card is not detected.
bash-3.00# pkgchk INTCGigaE
ERROR:... (0 Replies)
Discussion started by: paventhan
0 Replies
7. Windows & DOS: Issues & Discussions
Hi,
I am struggling in installing TK module for strawberry perl.
I downloaded TK804 module,
extracted to a folder, kept in c:/strawberry/perl/lib path,
then from tht path
1) perl makefile.pl
2)dmake
3)dmake test
4)dmake install
During perl makefile.pl it is giving error as... (3 Replies)
Discussion started by: vasanth.vadalur
3 Replies
8. Shell Programming and Scripting
Hi 'm getting error while installing perl mdule on linux.can any one tell me how to resolve that error?
problem is:
CPAN: File::Temp loaded ok (v0.22)
CPAN.pm: Going to build J/JD/JDB/Win32-OLE-0.1709.tar.gz
OS unsupported
Warning: No success on command
Warning (usually harmless):... (1 Reply)
Discussion started by: kavi.mogu
1 Replies
9. Red Hat
Hi,
I am using Red Hat 9.0 and it does not have the inbuilt driver module for my onboard lan card (RTL 8169). I downloaded the module (file - r8169-6.017.00.tar.bz2 and even r8169-6.015.00.tar.bz2), but when try to install it it says r8169.h , r8169_n.c , Makefile etc are not ELF formats.
... (0 Replies)
Discussion started by: dextergenious
0 Replies
10. Shell Programming and Scripting
I have issue with the perl module installed in the new Linux server
I have installed the required module, but still the perl program was not able to find the path
I'm getting the below error:
Can't locate Log/Log4perl.pm in @INC (@INC contains: /usr/lib/perl5/site_perl/Log4perl.pm... (5 Replies)
Discussion started by: help_scr_seeker
5 Replies
LEARN ABOUT CENTOS
dh_auto_install
DH_AUTO_INSTALL(1) Debhelper DH_AUTO_INSTALL(1)
NAME
dh_auto_install - automatically runs make install or similar
SYNOPSIS
dh_auto_install [buildsystemoptions] [debhelperoptions] [--params]
DESCRIPTION
dh_auto_install is a debhelper program that tries to automatically install built files. It does so by running the appropriate command for
the build system it detects the package uses. For example, if there's a Makefile and it contains a install target, then this is done by
running make (or MAKE, if the environment variable is set). If there is a setup.py or Build.PL, it is used. Note that the Ant build system
does not support installation, so dh_auto_install will not install files built using Ant.
Unless --destdir option is specified, the files are installed into debian/package/ if there is only one binary package. In the multiple
binary package case, the files are instead installed into debian/tmp/, and should be moved from there to the appropriate package build
directory using dh_install(1).
DESTDIR is used to tell make where to install the files. If the Makefile was generated by MakeMaker from a Makefile.PL, it will
automatically set PREFIX=/usr too, since such Makefiles need that.
This is intended to work for about 90% of packages. If it doesn't work, or tries to use the wrong install target, you're encouraged to skip
using dh_auto_install at all, and just run make install manually.
OPTIONS
See "BUILD SYSTEM OPTIONS" in debhelper(7) for a list of common build system selection and control options.
--destdir=directory
Install files into the specified directory. If this option is not specified, destination directory is determined automatically as
described in the "DESCRIPTION" section.
-- params
Pass params to the program that is run, after the parameters that dh_auto_install usually passes.
SEE ALSO
debhelper(7)
This program is a part of debhelper.
AUTHOR
Joey Hess <joeyh@debian.org>
11.1.6ubuntu2 2018-05-10 DH_AUTO_INSTALL(1)