07-24-2012
Network card module installation
Hi,
I am using Red Hat 9.0 and it does not have the inbuilt driver module for my onboard lan card (RTL 8169). I downloaded the module (file - r8169-6.017.00.tar.bz2 and even r8169-6.015.00.tar.bz2), but when try to install it it says r8169.h , r8169_n.c , Makefile etc are not ELF formats.
After downlaoding , I did
Make clean modules - Multiple errors
Make install - multiple errors
depmod -a etc. - Files are not valid ELF format
I have checked lspci and my card is shown there with No driver installed.
Module (after extracting ) contains Makefile, Makefile_2.4.x , r8169.h, r8169_n.c, readme. I tried to build the source with its Makefile which also gives multiple errors saying that the parameters in Makefile not found.
Help me out of this !!!
Thanks,
Dexter
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. Solaris
hello solaris friends,
I've tried installing Sun Solaris 10.0, but everytime it seems to bypass the network config. screen that looks similar to this...here's the url:
http://www.hup.hu/old/images/hup/Solaris/Sol10beta7/9.png
I'm able to install it all the way through but I get no... (2 Replies)
Discussion started by: cadmiumgreen
2 Replies
3. UNIX for Advanced & Expert Users
Hi,
I am trying to install perl modules in HPUX under my account. I do not have the root permission.
The module name I am trying to install is Spreadsheet-WriteExcel. I have downloaded the tar.gz file from CPAN and extracted the same under my home directory.
When I try do 'perl... (2 Replies)
Discussion started by: sabyasm
2 Replies
4. Shell Programming and Scripting
Hi All,
I am failry new to Perl.I am trying to install a Perl module (Filesys::df.pm) in an IBM AIX5.3 server.But I could not succeed in that.I am getting the following error:
abcd3dev# make
cc_r -c -D_ALL_SOURCE -D_ANSI_C_SOURCE -D_POSIX_SOURCE -qmaxmem=16384 -qnoansialias... (6 Replies)
Discussion started by: surjithss
6 Replies
5. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
6. Solaris
I have installed Solaris 10 in my PC successfully and my system having Intel(R) PRO/100 VE ethernet card. Solaris OS not able to detect the network card. So i checked the driver (INTCGigaE) and reinstalled. Still network card is not detected.
bash-3.00# pkgchk INTCGigaE
ERROR:... (0 Replies)
Discussion started by: paventhan
0 Replies
7. Windows & DOS: Issues & Discussions
Hi,
I am struggling in installing TK module for strawberry perl.
I downloaded TK804 module,
extracted to a folder, kept in c:/strawberry/perl/lib path,
then from tht path
1) perl makefile.pl
2)dmake
3)dmake test
4)dmake install
During perl makefile.pl it is giving error as... (3 Replies)
Discussion started by: vasanth.vadalur
3 Replies
8. Shell Programming and Scripting
Hi 'm getting error while installing perl mdule on linux.can any one tell me how to resolve that error?
problem is:
CPAN: File::Temp loaded ok (v0.22)
CPAN.pm: Going to build J/JD/JDB/Win32-OLE-0.1709.tar.gz
OS unsupported
Warning: No success on command
Warning (usually harmless):... (1 Reply)
Discussion started by: kavi.mogu
1 Replies
9. Red Hat
Hi,
I am using Red Hat 9.0 and it does not have the inbuilt driver module for my onboard lan card (RTL 8169). I downloaded the module (file - r8169-6.017.00.tar.bz2 and even r8169-6.015.00.tar.bz2), but when try to install it it says r8169.h , r8169_n.c , Makefile etc are not ELF formats.
... (0 Replies)
Discussion started by: dextergenious
0 Replies
10. Shell Programming and Scripting
I have issue with the perl module installed in the new Linux server
I have installed the required module, but still the perl program was not able to find the path
I'm getting the below error:
Can't locate Log/Log4perl.pm in @INC (@INC contains: /usr/lib/perl5/site_perl/Log4perl.pm... (5 Replies)
Discussion started by: help_scr_seeker
5 Replies
LEARN ABOUT CENTOS
opensc-tool
OPENSC-TOOL(1) OpenSC Tools OPENSC-TOOL(1)
NAME
opensc-tool - generic smart card utility
SYNOPSIS
opensc-tool [OPTIONS]
DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
sending arbitrary APDU commands to a card.
OPTIONS
--atr, -a
Print the Answer To Reset (ATR) of the card. Output is in hex byte format
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--info, -i
Print information about OpenSC, such as version and enabled components.
--list-drivers, -D
List all installed card drivers.
--list-files, -f
Recursively list all files stored on card.
--list-readers, -l
List all configured readers.
--name, -n
Print the name of the inserted card (driver).
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF....
--serial
Print the card serial number (normally the ICCSN). Output is in hex byte format
--verbose, -v
Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
--wait, -w
Wait for a card to be inserted.
SEE ALSO
opensc-explorer(1)
opensc 06/17/2014 OPENSC-TOOL(1)