07-23-2012
For this you have to grep for
/opt/temp/abc.pcap so that it just gives you single ID!! Hope this will help!
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi all,
I have a script like:
echo Please input list file name:
read listn
for file in `cat $listn.txt`
do
send_file $file
done
normally, I will run the script like:
:. resendfile
Please input list filename:
list1
#Then, the script will resend all file from the list1. However,... (4 Replies)
Discussion started by: happyv
4 Replies
2. Shell Programming and Scripting
Hi All,
Have a script called FTPIN-xx.sh.
It does stuff and when all is done, it is to execute another.
However, I'd like to have it execute the second script in the background or in a fashion that would allow my script to complete without having to wait.
I'm robbing the command from how I... (2 Replies)
Discussion started by: Cameron
2 Replies
3. Shell Programming and Scripting
Hi,
I want to write a script that checks an interface with the snoop command, if there is no traffic in 10 minutes on port 123 from the ip add 10.*.*.* it should send a e-mail.but i don't know how to start writing this script does anybody have an idea or an sample script that i can modifi.
... (2 Replies)
Discussion started by: tafil
2 Replies
4. Shell Programming and Scripting
Hi all,
I want to monitoring my interface every 6 hours where i want to run snoop command to capture all packet through the interface, so i want running snoop then snoop will run for 5 minutes after that snoop stop then will start again after 6 hours than run for 5 minutes again.
thereis any... (9 Replies)
Discussion started by: tindasz
9 Replies
5. Shell Programming and Scripting
Hi all,
I am having a script ScriptA which is calling a script ScriptB in the same server and copying files to second server and have to execute one script ScriptC in the second server. THis First script ScriptA is the main script and i have to execute this process continously.
for Keeping... (2 Replies)
Discussion started by: rohithji
2 Replies
6. Solaris
Hi ,
I would like to write a perl script with the snoop command to capture packets from a specific IP address to a node (incoming packets) and packets from that node for the same session to another node and save the capture to a file. I would like my script to be able to read my IP all the time... (7 Replies)
Discussion started by: Pouchie1
7 Replies
7. Shell Programming and Scripting
Hi Everyone :),
Need your advice as I'm new to UNIX scripting.. I'm trying to write a script to capture snoop output for 5 minutes for every hour for 24 hours. To stop snoop, I need to press Control-C to break it. This is what I got so far, but now I'm stuck! :confused:
The script:
# cat... (2 Replies)
Discussion started by: faraaris
2 Replies
8. Shell Programming and Scripting
Hi all,
I have a script that calls another program/script, xxx, to run in the background. Supposedly this program at most should finish within five (5) minutes so after five (5) minutes, I run some other steps to run the script into completion.
My problem is sometimes the program takes... (5 Replies)
Discussion started by: newbie_01
5 Replies
9. Shell Programming and Scripting
I have a script called startWebLogic.sh which I was running in the background but the problem is which I used the command :- ps -elf | grep "startWebLogic.sh" | grep -v grep to find the process id but I was unable to find the process id for this script and when I checked from the front end the... (3 Replies)
Discussion started by: maitree
3 Replies
10. Shell Programming and Scripting
Hi,
I want to write a script which continuously checking status of a script running in background by nohup command. And if same script is not running then immediately start the script...please help..
i am using below command to run script
nohup system_traps.sh &
but in some... (9 Replies)
Discussion started by: ketanraut
9 Replies
LEARN ABOUT NETBSD
pcap_fopen_offline
PCAP_OPEN_OFFLINE(3PCAP) PCAP_OPEN_OFFLINE(3PCAP)
NAME
pcap_open_offline, pcap_fopen_offline - open a saved capture file for reading
SYNOPSIS
#include <pcap/pcap.h>
char errbuf[PCAP_ERRBUF_SIZE];
pcap_t *pcap_open_offline(const char *fname, char *errbuf);
pcap_t *pcap_fopen_offline(FILE *fp, char *errbuf);
DESCRIPTION
pcap_open_offline() is called to open a ``savefile'' for reading.
fname specifies the name of the file to open. The file can have the pcap file format as described in pcap-savefile(5), which is the file
format used by, among other programs, tcpdump(1) and tcpslice(1), or can have the pcap-ng file format, although not all pcap-ng files can
be read. The name "-" in a synonym for stdin.
Alternatively, you may call pcap_fopen_offline() to read dumped data from an existing open stream fp. Note that on Windows, that stream
should be opened in binary mode.
RETURN VALUE
pcap_open_offline() and pcap_fopen_offline() return a pcap_t * on success and NULL on failure. If NULL is returned, errbuf is filled in
with an appropriate error message. errbuf is assumed to be able to hold at least PCAP_ERRBUF_SIZE chars.
SEE ALSO
pcap(3PCAP), pcap-savefile(5)
5 April 2008 PCAP_OPEN_OFFLINE(3PCAP)