07-19-2012
Here's an update.
I tried to use DHCP and it worked! Then I reconfigured it back to use static IP and it stopped working again. After a while, it just started working
I don't have time to figure out what I did to fix it at at this point but will check back later..
Thanks for all the help
10 More Discussions You Might Find Interesting
1. AIX
I have a P570 that for some reason is not allowing the P1-T6 NIC to be recognized. I have confirmed from the HMC that it is set for the LPAR, but when I do a cfgmgr, it won't recognize it. It though is recognizing the slot cards just fine which are P1-C3 for one shelf and P1-C3 of another shelf.... (1 Reply)
Discussion started by: LegendMan
1 Replies
2. IP Networking
Dear friends,
Please explain the functionality of the ping command and explain the network details, and IP layers.
I want some more clarification about following things
i) switch
ii) hub
iii) routers
iv) proxy (3 Replies)
Discussion started by: thangappan
3 Replies
3. AIX
I am planning for System P with 2 number of 2-core processor (4 core in total).
Can I make 3 LPARS with this processor configuration without the support of micropartitioning, that means with simple LPAR only. (3 Replies)
Discussion started by: pchangba
3 Replies
4. AIX
can i get a step b syep explanation in creating LPAR... i have searched for tutorials i couldn't find the right one.... (2 Replies)
Discussion started by: udtyuvaraj
2 Replies
5. AIX
Hi all,
I have the following configuration
2 ds3524 storage disk systems located over 2 locations
2 P720 server located over 2 locations
DS3524 are connected to san switch.
Each vio server has 1 fc adapter attached to a san switch.
per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Discussion started by: markiemark
2 Replies
6. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
7. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
8. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
9. AIX
There can be configurations in IBM Server wherein a
standalone partition is created on some supported IBM Server
Or
A VIOS - VIOC LPARs created.
Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..?
On a... (2 Replies)
Discussion started by: Manish00712
2 Replies
10. Programming
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
mcd(1) General Commands Manual mcd(1)
NAME
mcd - mtools utility to change or report the DOS working directory
SYNOPSIS
mcd [msdosdirectory]
DESCRIPTION
Without arguments, the mcd command reports the current device and working directory. Otherwise, the mcd command changes the current device
and current working directory relative to a DOS file system. Unlike the DOS command CD, the mcd command can be used to change to another
device.
The environment variable MCWD can be used to locate the file where the device and current working directory information is stored. The
default is $HOME/.mcwd. The file is created if it does not exist and a msdosdirectory is specified.
DOS pathnames that contain the '/' or '' separator are supported. If you use the '' separator or wildcards, you must enclose file names
in quotes to protect them from the shell.
The mcd command supports the use of to move back one directory in the tree, however, multiple relative moves such as are not supported and
do not affect your current position in the directory tree.
NOTES
At logout time, it is advisable to remove old files.
EXIT STATUS
The following exit values are returned: Success. Failure.
ENVIRONMENT VARIABLES
The following environment variables affect the execution of mcd: If set, this variable names the file that contains the name of the current
mtools working directory as established by the mcd command. If this variable is not set, the file $HOME/.mcwd is used.
FILES
Contains the name of the current mtools working directory as established by the mcd command. If this file does not exist, the default
mtools working directory is A:. Executable file
SEE ALSO
Commands: mdir(1), mtools(1)
mcd(1)