LPAR Networking: Can't ping Post: 302673231

10 More Discussions You Might Find Interesting

1. AIX

LPAR and CFGMGR

I have a P570 that for some reason is not allowing the P1-T6 NIC to be recognized. I have confirmed from the HMC that it is set for the LPAR, but when I do a cfgmgr, it won't recognize it. It though is recognizing the slot cards just fine which are P1-C3 for one shelf and P1-C3 of another shelf....

2. IP Networking

ping and networking

Dear friends, Please explain the functionality of the ping command and explain the network details, and IP layers. I want some more clarification about following things i) switch ii) hub iii) routers iv) proxy

3. AIX

LPAR

I am planning for System P with 2 number of 2-core processor (4 core in total). Can I make 3 LPARS with this processor configuration without the support of micropartitioning, that means with simple LPAR only.

4. AIX

LPAR creation

can i get a step b syep explanation in creating LPAR... i have searched for tutorials i couldn't find the right one....

5. AIX

LPAR freezes after switching of storage (lpar is mirrored)

Hi all, I have the following configuration 2 ds3524 storage disk systems located over 2 locations 2 P720 server located over 2 locations DS3524 are connected to san switch. Each vio server has 1 fc adapter attached to a san switch. per p720 server 2 virtual io servers. Vio 1 has 1 lun...

6. Shell Programming and Scripting

Animation Ping on Solaris Like Cisco Ping

Hi, I develop simple animation ping script on Solaris Platform. It is like Cisco ping. Examples and source code are below. bash-3.00$ gokcell 152.155.180.8 30 Sending 30 Ping Packets to 152.155.180.8 !!!!!!!!!!!!!.!!!!!!!!!!!!!!!. % 93.33 success... % 6.66 packet loss......

7. AIX

Networking Issue (Cant Ping the gateway)

Hi, I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure? Is there anything that I have to check with vio setting or Am I missing any configuration? Please let me know further. Thank you

8. Shell Programming and Scripting

How to get reason for ping failure using perls Net::Ping->new("icmp");?

Hi I am using perl to ping a list of nodes - with script below : $p = Net::Ping->new("icmp"); if ($p->ping($host,1)){ print "$host is alive.\n"; } else { print "$host is unreacheable.\n"; } $p->close();...

9. AIX

How to differentiate between a standalone LPAR and a VIOC (which again is a lpar)?

There can be configurations in IBM Server wherein a standalone partition is created on some supported IBM Server Or A VIOS - VIOC LPARs created. Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..? On a...

10. Programming

Ping test sends mail when ping fails

help with bash script! im am working on this script to make sure my server will stay online, so i made this script.. HOSTS="192.168.138.155" COUNT=4 pingtest(){ for myhost in "$@" do ping -c "$COUNT" "$myhost" &&return 1 done return 0 } if pingtest $HOSTS #100% failed...

LEARN ABOUT DEBIAN

mrtg-ping-probe

MRTG-PING-PROBE(1)					      General Commands Manual						MRTG-PING-PROBE(1)

NAME

       mrtg-ping-probe - ping probe module for Multi Router Traffic Grapher

DESCRIPTION

       mrtg-ping-probe is a ping probe module for MRTG 2.x.  It is used to monitor the round trip time and packet loss to networked devices.  MRTG
       uses the output of mrtg-ping-probe to generate graphs visualizing minimum and maximum round trip times or packet loss.

       mrtg-ping-probe is not run directly, but is called by MRTG as a helper when it needs to determine ping time to a host.

       Act responsibly: do not use mrtg-ping-probe to ping devices without the owner's permission.  Just imagine if 10,000 people decided to  ping
       your hosts!  mrtg-ping-probe is meant to be used within your network to get round trip time performance figures for your network.

OPTIONS

       To  use	mrtg-ping-probe you need to configure MRTG to call it from within the definition of a target host. This is done in the MRTG config
       file, which is usually /etc/mrtg.conf.

       Here's an example snippet: change the target name and IP address to suit your needs.

       Target[your.target.ping]: `/usr/bin/mrtg-ping-probe 123.456.789.123`
       SetEnv[your.target.ping]: MRTG_INT_IP="123.456.789.123" MRTG_INT_DESCR="ping"
       MaxBytes[your.target.ping]: 100
       AbsMax[your.target.ping]: 200
       Options[your.target.ping]: gauge, growright
       YLegend[your.target.ping]: ping time (ms)
       ShortLegend[your.target.ping]: ms
       Legend1[your.target.ping]: Maximum Round Trip Time in ms
       Legend2[your.target.ping]: Minimum Round Trip Time in ms
       Legend3[your.target.ping]: Maximal 5 Minute Maximum Round Trip Time in ms
       Legend4[your.target.ping]: Maximal 5 Minute Minimum Round Trip Time in ms
       LegendI[your.target.ping]: &nbsp;Max:
       LegendO[your.target.ping]: &nbsp;Min:

       Pay close attention to the backticks in the first line which tell MRTG to execute the nominated external program. Note also that  you  need
       to use the "gauge" option, since the results of subsequent ping probes are independant values and not an incrementing counter.

SEE ALSO

       mrtg(1).

       The latest release of mrtg-ping-probe can be found on the web at http://pwo.de/projects/mrtg/

AUTHOR

       This manual page was written by Jonathan Oxer <jon@debian.org>, for the Debian project (but may be used by others).

								  April 14, 2003						MRTG-PING-PROBE(1)

10 More Discussions You Might Find Interesting

1. AIX

LPAR and CFGMGR

Discussion started by: LegendMan

2. IP Networking

ping and networking

Discussion started by: thangappan

3. AIX

LPAR

Discussion started by: pchangba

4. AIX

LPAR creation

Discussion started by: udtyuvaraj