07-17-2012
You need a gateway or an adapter into that other subnet. So is 10.1.40.1 a gateway? Is it up and running?
10 More Discussions You Might Find Interesting
1. AIX
I have a P570 that for some reason is not allowing the P1-T6 NIC to be recognized. I have confirmed from the HMC that it is set for the LPAR, but when I do a cfgmgr, it won't recognize it. It though is recognizing the slot cards just fine which are P1-C3 for one shelf and P1-C3 of another shelf.... (1 Reply)
Discussion started by: LegendMan
1 Replies
2. IP Networking
Dear friends,
Please explain the functionality of the ping command and explain the network details, and IP layers.
I want some more clarification about following things
i) switch
ii) hub
iii) routers
iv) proxy (3 Replies)
Discussion started by: thangappan
3 Replies
3. AIX
I am planning for System P with 2 number of 2-core processor (4 core in total).
Can I make 3 LPARS with this processor configuration without the support of micropartitioning, that means with simple LPAR only. (3 Replies)
Discussion started by: pchangba
3 Replies
4. AIX
can i get a step b syep explanation in creating LPAR... i have searched for tutorials i couldn't find the right one.... (2 Replies)
Discussion started by: udtyuvaraj
2 Replies
5. AIX
Hi all,
I have the following configuration
2 ds3524 storage disk systems located over 2 locations
2 P720 server located over 2 locations
DS3524 are connected to san switch.
Each vio server has 1 fc adapter attached to a san switch.
per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Discussion started by: markiemark
2 Replies
6. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
7. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
8. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
9. AIX
There can be configurations in IBM Server wherein a
standalone partition is created on some supported IBM Server
Or
A VIOS - VIOC LPARs created.
Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..?
On a... (2 Replies)
Discussion started by: Manish00712
2 Replies
10. Programming
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)
NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO
vconfig(8) interfaces(5)
vlan September 30 2007 VLAN-INTERFACES(5)