I appreciate your input and I had no idea you could use paste like this too so thanks so much for that. The results put everything with a tab after the delimiter. I want all fields concatenated but just not the names themselves concatenated like the example I had:
Actually I would like to eliminate the first field too (the record numbers portion - 1, 2 etc.). The last field should have a trailing ";". Sorry I didn't say that before. Even if I take what you had and run it through awk email addresses will have a leading space if the previous name field did not use a middle initial.
Hello,
I have two files that I need to compare and print out the line from file2 that has the first 6 fields matching the first 6 fields in file1. Complicating this are the following restrictions
1. file1 is only a few thousand lines at most and file2 is greater than 2 million
2. I need to... (7 Replies)
Hi All,
I'm trying to figure out which are the trusted-ips and which are not using a script file.. I have a file named 'ip-list.txt' which contains some ip addresses and another file named 'trusted-ip-list.txt' which also contains some ip addresses. I want to read a line from... (4 Replies)
input:
field1
field2
field3 field4
output:
"field1";"field2";"field3";"field4"
My input file is shown above and I want output as shown using awk. the length of field3 is fixed so, the space between field3 and field4 can vary according to the value of field3. I am new to unix, so... (1 Reply)
input:
field1
field2
field3 field4
output:
"field1";"field2";"field3";"field4"
My input file is shown above and I want output as shown using awk. the length of field3 is fixed so, the space between field3 and field4 can vary according to the value of field3. I am new to unix, so can... (5 Replies)
Hi all,
I have a single line output like below
echo $ips
10.26.208.28 10.26.208.26 10.26.208.27
want to convert above single line output as below format. Pls advice how to do ?
10.26.208.28
10.26.208.26
10.26.208.27
Regards
Kannan (6 Replies)
I am new to awk scripting.
I want to do a field by word (field) comparison of two files File1.txt and File2.txt.
The files contain a list of | (pipe) separated field.
**File 1:
-------------------
aaa|bbb|ccc|eee|fff
lll|mmm|nnn|ooo|ppp
rrr|sss|ttt|uuu|vvv**
File 2: ... (7 Replies)
Hi,
i have a scenario were i should compare a few fields from each line then increment a variable based on that.
Example file
989878|8999|Y|0|Y|N|V
989878|8999|Y|0|N|N|V
989878|8999|Y|2344|Y|N|V
i have 3 conditions to check and increment a variable on every line
condition 1 if ( $3... (4 Replies)
GIT-CHECK-MAILMAP(1) Git Manual GIT-CHECK-MAILMAP(1)NAME
git-check-mailmap - Show canonical names and email addresses of contacts
SYNOPSIS
git check-mailmap [options] <contact>...
DESCRIPTION
For each "Name <user@host>" or "<user@host>" from the command-line or standard input (when using --stdin), look up the person's canonical
name and email address (see "Mapping Authors" below). If found, print them; otherwise print the input as-is.
OPTIONS --stdin
Read contacts, one per line, from the standard input after exhausting contacts provided on the command-line.
OUTPUT
For each contact, a single line is output, terminated by a newline. If the name is provided or known to the mailmap, "Name <user@host>" is
printed; otherwise only "<user@host>" is printed.
MAPPING AUTHORS
If the file .mailmap exists at the toplevel of the repository, or at the location pointed to by the mailmap.file or mailmap.blob
configuration options, it is used to map author and committer names and email addresses to canonical real names and email addresses.
In the simple form, each line in the file consists of the canonical real name of an author, whitespace, and an email address used in the
commit (enclosed by < and >) to map to the name. For example:
Proper Name <commit@email.xx>
The more complex forms are:
<proper@email.xx> <commit@email.xx>
which allows mailmap to replace only the email part of a commit, and:
Proper Name <proper@email.xx> <commit@email.xx>
which allows mailmap to replace both the name and the email of a commit matching the specified commit email address, and:
Proper Name <proper@email.xx> Commit Name <commit@email.xx>
which allows mailmap to replace both the name and the email of a commit matching both the specified commit name and email address.
Example 1: Your history contains commits by two authors, Jane and Joe, whose names appear in the repository under several forms:
Joe Developer <joe@example.com>
Joe R. Developer <joe@example.com>
Jane Doe <jane@example.com>
Jane Doe <jane@laptop.(none)>
Jane D. <jane@desktop.(none)>
Now suppose that Joe wants his middle name initial used, and Jane prefers her family name fully spelled out. A proper .mailmap file would
look like:
Jane Doe <jane@desktop.(none)>
Joe R. Developer <joe@example.com>
Note how there is no need for an entry for <jane@laptop.(none)>, because the real name of that author is already correct.
Example 2: Your repository contains commits from the following authors:
nick1 <bugs@company.xx>
nick2 <bugs@company.xx>
nick2 <nick2@company.xx>
santa <me@company.xx>
claus <me@company.xx>
CTO <cto@coompany.xx>
Then you might want a .mailmap file that looks like:
<cto@company.xx> <cto@coompany.xx>
Some Dude <some@dude.xx> nick1 <bugs@company.xx>
Other Author <other@author.xx> nick2 <bugs@company.xx>
Other Author <other@author.xx> <nick2@company.xx>
Santa Claus <santa.claus@northpole.xx> <me@company.xx>
Use hash # for comments that are either on their own line, or after the email address.
GIT
Part of the git(1) suite
Git 2.17.1 10/05/2018 GIT-CHECK-MAILMAP(1)