Hi,
I have data in the following format:
data1
data2 data3 data4
data5 data6
data7 data8 data9
data10
I require the final output to be:
data1
data1
data1
data1
i only require the 1st line but I need to replicate it in n rows where n is the number of rows where data... (4 Replies)
Discussion started by: ReV
4 Replies
2. Post Here to Contact Site Administrators and Moderators
I have a B180L controller running HP-UX 10.2 with an internal DDS2 tape drive and an external Surestore DDS (24gb) tape drive. I want to make duplicate copies of ignite tapes from one tape drive to another. What is the best way to do this? (1 Reply)
Hi,
i have a webserver logfile and want to count how many page views there have been.
I was thinking about removing lines that begin with the same user and same date&time, because it indicates they were just looking at one page and multiple hits were counted.
My question is how do I do this?... (6 Replies)
Hi guys,
Suppose you have a server with two ethernet cards (1GB each) and each cards are connecting to two different switches cisco 3750. My question is:
How can I setup my server's network interfaces to increase the throughput up to 2GB? is it possible? If not, do you know another way to up... (3 Replies)
hi guys
I have a IBM eServer BladeCenter HS12 with Linux Red Hat 5.4 installed on it, it is using Bonding.
ifcfg-bond0
DEVICE=bond0
BOOTPROTO=none
ONBOOT=yes
TYPE=Ethernet
IPADDR=x.x.x.x
NETMASK=x.x.x.x
GATEWAY=x.x.x.x
USERCTL=no
IPV6INIT=no
PEERDNS=no
BONDING_OPTS="miimon=80... (1 Reply)
Hi Folks,
I've put together a script for sorting my backup files into sub folders to be run from a cron job. Each file is named username.tar.gz and the file /etc/trueuserowners contains all users and their owner in the format "user: owner".
The script works fine identifying users and their owners... (10 Replies)
Hello,
I have a file named file_1.sh that I want to duplicate into file_2.sh, file_3.sh,..., etc.
I also need to change the text within each file so that it would fit the file name. For example, in file_1.sh there is a command to save some output as 'output_1.txt', and also there is an input... (3 Replies)
Discussion started by: haguyw
3 Replies
LEARN ABOUT HPUX
fmt
fmt(1) General Commands Manual fmt(1)NAME
fmt - format text
SYNOPSIS
width] [file...]
DESCRIPTION
The command is a simple text formatter that fills and joins lines to produce output lines of (up to) the number of characters specified in
the width option. The default width is 72. concatenates the arguments. If none are given, formats text from the standard input.
Blank lines are preserved in the output, as is the spacing between words. does not fill lines beginning with a period for compatibility
with Nor does it fill lines starting with
Indentation is preserved in the output and input lines with differing indentation are not joined (unless is used).
can also be used as an in-line text filter for the command:
reformats the text between the cursor location and the end of the paragraph.
Options
recognizes the following options:
Crown margin mode.
Preserve the indentation of the first two lines within a paragraph and align the left margin of each subsequent line with that
of the second line. This is useful for tagged paragraphs.
Split lines only.
Do not join short lines to form longer ones. This prevents sample lines of code, and other such "formatted" text, from being
unduly combined.
Fill output lines to up to
width columns.
WARNINGS
The width option is acceptable for BSD compatibility, but it may go away in future releases.
SEE ALSO nroff(1), vi(1).
fmt(1)