07-06-2012
I think That I understand the question being asked by NH2.
There's a system with two interfaces A and B connected to A and B LAN's. Interface A is up and working with an ip address and LAN A users can access it.
Interface B is down (no ip address) but is there a way that LAN B users could be told (by enquiring on the MAC address or something) that the system has an alternative address on LAN A (assuming of course that there is a gateway between LAN A and LAN B that they could go through).
The only answer that I can think of (and I'm not a networking guru) is, yes, let them call for the system by name and use a DNS server.
9 More Discussions You Might Find Interesting
1. AIX
Hey all. I have a long list of IP addresses I want to ping. The IP's are located in a flat file "ping_info.dat".
I was wondering what the best way to go about this would be. Can someone help me out? (2 Replies)
Discussion started by: jalge2
2 Replies
2. Shell Programming and Scripting
Hi,
How to ping an ip from an unix machine. Can you please let me know the exact command. I used and i got the below error
ping 171.18.17.2
bash: ping: command not found
Thanks n regards
Ammu (1 Reply)
Discussion started by: ammu
1 Replies
3. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
4. Shell Programming and Scripting
Keep in mind that I haven't done Perl scripting for a LONG time, so I'm quite rusty.
This is what I would like to do:
- using fork, create 3 or 4 processes to read 3 or 4 different text documents containing server names or IP addresses
- in each of those processes, Perl will ping each of those... (7 Replies)
Discussion started by: kooshi
7 Replies
5. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
6. Solaris
Dear all,
I face some problem as below.
I have a sun fire 280r server in a network. From that server i am able to ping any system in any network. But i am facing the problem when i try to ping the server from outside netwok. Once i give ping command in the server then only i try to... (1 Reply)
Discussion started by: sudhansu
1 Replies
7. Shell Programming and Scripting
how can you ping a domain and store the ip?
like given a url in a variable $url
how can i ping it?
also how can i find the local server's ip address on a cpanel server?
(i have multiple servers and didnt want to hard code it in)
(basically i want to check the domain accounts on the server,... (11 Replies)
Discussion started by: vanessafan99
11 Replies
8. UNIX Desktop Questions & Answers
I need to ping websites and I need to see which one has the highest delay.
My problem is I need to extract the name Facebook and the time=74.0 ms using awk. I need help doing this please...
PING facebook.com (173.252.90.36) 56(84) bytes of data.
64 bytes from... (5 Replies)
Discussion started by: 5sku5
5 Replies
9. Emergency UNIX and Linux Support
Hi,
I need to set up a script that would write the results of the ping command from one AIX server to another file may be every minute. Like this I need to gather the data for a period of 24 hours.
Can someone please help me with this?
G (5 Replies)
Discussion started by: ggayathri
5 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)
NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO
vconfig(8) interfaces(5)
vlan September 30 2007 VLAN-INTERFACES(5)