I have two net-card. one is 172.16.24.99(ENG) ,another is 172.16.25.99(ENG-B). Both masks is 255.255.255.0.
I will monitor data on the tcp port 8055 in ENG, How do I set option of tcpdump command (2 Replies)
i would like to know about tcpdump
i would like to use tcpdump to get information about these
- Date
- time
- source hostname
- source mac address
- source ip address
- destination ip address
- see outbound only
then i use command like this
tcpdump -i le0 -n -q -tttt -e src net... (0 Replies)
i would like to know about tcpdump
i would like to use tcpdump to get information about these
- Date
- time
- source hostname
- source mac address
- source ip address
- destination ip address
- see outbound only
then i use command like this
tcpdump -i le0 -n -q -tttt -e src net... (2 Replies)
Hello there,
My mulithreaded application (which is too large to represent the source code here) is crashing after installing FreeBSD 7.1-RELEASE/amd64.
It worked properly on others machines (Dual Cores with 4GB of RAM - FreeBSD 6.2-RELEASE/i386).
The current machine has 2x Core 2 Duo... (1 Reply)
Hi.
Need Help with TcpDump
Trying to sniff associatio-request with tcpdump but when i run this tcpdump -i eth0 wlan subtype assoc-req i get this error
can anyone help me with this error ? Thanks alot !!:) (1 Reply)
Hello everyone, so I'm getting this tcpdump, and it looks like..quite a mess... Can anyone decipher this? I can tell that one IP is requesting DNS info? but I'm having trouble finding out what some of the fields actually mean..
19:44:50.707637 IP 66.81.1.252.53 > 64.147.113.139.28638: 52313... (4 Replies)
I've recently started learning to use TCPdump, and I find it pretty interesting. There's one thing I don't understand. When I tell it to capture packets on, say, the WiFi interface en1, it often captures packets sent or received by other hosts on the network. How can it do this? My... (3 Replies)
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
LEARN ABOUT DEBIAN
tracestats
TRACESTATS(1) User Commands TRACESTATS(1)NAME
tracestats - perform simple analysis on a trace
SYNOPSIS
tracestats [ -f | --filter bpf ]... inputuri...
DESCRPTION
tracestats reads one or more traces and outputs summaries for each trace of how many packets/bytes match each bpf filter, as well as
totals. If instead of doing this for the entire trace, but to do it for portions then use tracertstats(1) instead.
-f bpf-filter
--filter bpf-filter
Add another bpf filter
EXAMPLES
tracestats --filter 'host sundown'
--filter 'port http'
--filter 'port ftp or ftp-data'
--filter 'port smtp'
--filter 'tcp[tcpflags] & tcp-syn!=0'
--filter 'not ip'
--filter 'ether[0] & 1 == 1'
--filter 'icmp[icmptype] == icmp-unreach'
erf:/traces/trace1.gz
erf:/traces/trace2.gz
LINKS
More details about tracestats (and libtrace) can be found at http://www.wand.net.nz/trac/libtrace/wiki/UserDocumentation
SEE ALSO libtrace(3), tracemerge(1), tracefilter(1), traceconvert(1), tracesplit(1), tracesplit_dir(1), tracereport(1), tracertstats(1), tracepkt-
dump(1), traceanon(1), tracesummary(1), tracereplay(1), tracediff(1), traceends(1), tracetopends(1)AUTHORS
Perry Lorier <perry@cs.waikato.ac.nz>
tracestats (libtrace) October 2005 TRACESTATS(1)