I'm not sure what is going wrong then, I suspect there is some issue with the ssh statement.
I ran the same logic on a test box and got the following output, so I know the statement works as intended:
If I then did an scp of foobar from Latitude to 10.5.113.88, a ls of /etc/network/foo* on 10.5.113.88 would show both files.
Can you include some debug echo statements in your code and see where it fails?
Hi,
How do i know if the files are transferred succesfully when i use SCP to transfer files between 2 servers.
One more is i am trying to send all the files in a single shot by using * to save the connection time. So can i know when the scp breakes in the middle
scp $sourcepath/*... (9 Replies)
Hi Frdz
I have a problem like.
I need to transfer a file from source to destination (different systems with different IPs) using "scp" command and before transfer the file i have to check the file is available in destination or not, if it is there no need to transfer, otherwise we have to... (5 Replies)
I have a shell script which uses SCP command to transfer the files from one server to another server. The files are getting transferred successfully, but the problem is the files transferred to the destination server didnot have the permissions as that of the files on the source server.
Command... (5 Replies)
FILE_LIST="{a.txt,b.txt,cal*}"
scp -r $..$REMOTE_PATH$FILE_LIST $LOCAL_PATH
This script passes only when all the three files are transfere, wat if only two file are transfered, but still I was to make the return code as pass.
is it possible. (2 Replies)
I am not able to throw a file from server173 to server067
i.e.
wlsuser@server173> scp /tmp/harsha.txt wlsuser@server067:/tmp
fails
However, I am able to pull a file from server173 onto server067's /tmp dir
wlsuser@server067> scp wlsuser@server173:/tmp/harsha.txt /tmp... (2 Replies)
Whenever I transfer file through SCP between two server it gives below given message.....Is there a way to avoid it....
Target server : newyork
$ scp ABC27801.iue newyork:./iABC/x0017801.iue
Message
=====
This system is for the use of authorized users only. Individuals using this... (1 Reply)
I have 3 AIX server namely - Server 1 , Server 2 and Server 3.
And have done SCP setup between Server 1 and Server 2 so that i dont have to give password when i transfer file from Server 1 to Server 2 by setting public key between the server.
Q1. If the unix password of the target server... (3 Replies)
On unix AIX server, when I am trying to transfer file from one directory to another directory on the same server through a program(where i call the script) it gives error "Lost Connection". (5 Replies)
I am testing the following command to transfer a file from my server (AIX 5.2) to another server. I was able to generate the keys and sent them the public key.
scp -v -P 4030 /home/lawson/.ssh/jimtest.txt someuser@some.ftpsite.net:/Inbound/jimtest.txt > jimtest_out.txt 2>&1
Based on... (3 Replies)
I am trying to transfer a zip file of around 30 MB in my automation script using scp from system A to B.
When I manually do scp, file is complete transferred but when automation shell script runs it, zip file is not completely transferred.
Stack Trace while doing manual :
Executing:... (1 Reply)
Discussion started by: Shaishav Shah
1 Replies
LEARN ABOUT DEBIAN
cksfv
CKSFV(1) General Commands Manual CKSFV(1)NAME
cksfv - tests and creates simple file verification (SFV) listings
SYNOPSIS
cksfv [-bciqrL] [-C dir] [-f file] [-g path] [file ...]
DESCRIPTION
cksfv is a tool for verifying CRC32 checksums of files. CRC32 checksums are used to verify that files are not corrupted. The algorithm is
cryptographically crippled so it can not be used for security purposes. md5sum (1) or sha1sum (1) are much better tools for checksuming
files. cksfv should only be used for compatibility with other systems.
cksfv has two operation modes: checksum creation and checksum verification
In checksum creation mode cksfv outputs CRC32 checksums of files to to stdout, normally redirected to an .sfv file.
In checksum verification mode cksfv reads filenames from an sfv file, and compares the recorded checksum values against recomputed check-
sums of files.
OPTIONS
These options are available
-b Strip dirnames from filenames that are checksumed. loads the files from original positions, but prints only basenames to catalogue
in sfv file.
-c Use stdout for printing progress and final resolution (files OK or some errors detected). This is useful for external programs
analysing output of cksfv. This also forces fflushes on the output when needed.
-C dir Change current directory before proceeding with a verification operation. This option is mostly obsoleted with -g option. Earlier
this was used to verify checksums in a different directory: cksfv -C foo -f foo/bar.sfv
-f file
Verify checksums in the sfv file
-g file
Change current directory to the path name of the file and verify checksums in the sfv.
-i Ignore case in filenames. This is used in the checksum verification mode.
-L Follow symlinks when recursing subdirectories. This option is used with the -r option.
-q Enable QUIET mode (instead of verbose mode), only error messages are printed
-v Enable VERBOSE mode, this is the default mode
-r recurse directories and check the .sfv files in each. Symlinks are not followed by default. This option cannot be used with -f and
-g options.
EXAMPLES
Verify checksums of files listed in 'foo/files.sfv':
cksfv -g foo/files.sfv
Create checksums for a set of files:
cksfv *.gz > files.sfv
Verify checksums of case-insensitive filenames listed in 'files.sfv'.
This is sometimes useful with files created by operating systems
that have case-insensitive filesystem names.
cksfv -i -g files.sfv
Check checksums of files 'foo' and 'bar' listed in 'files.sfv':
cksfv -g files.sfv foo bar
Create checksums of files matching /foo/bar/* and strip dirnames away:
cksfv -b /foo/bar/* > files.sfv
Recursively scan /foo/bar and verify each .sfv file:
cksfv -C /foo/bar -r
Same as previous, but starting from the current working directory
and also following symlinks during recursion:
cksfv -r -L
SEE ALSO basename(1)dirname(1)md5sum(1)sha1sum(1)AUTHOR
This manual page was originally written by Stefan Alfredsson <stefan@alfredsson.org>. It was later modified by Heikki Orsila
<heikki.orsila@iki.fi> and Durk van Veen <durk.van.veen@gmail.com>.
CKSFV(1)