Sponsored Content
Special Forums Cybersecurity How to disable TLS 1.0 support in Solaris Post 302662431 by bitlord on Tuesday 26th of June 2012 02:31:26 PM
Old 06-26-2012
It looks like Oracle says that this is a Java issue (JDK and JRE 7, 6 Update 27 and before, 5.0 Update 31 and before, 1.4.2_33 and before. JRockit R28.1.4 and before). Oracle says if your Java level is higher then the version above, your good. If not patch Java.

ref: Oracle Java Critical Patch Update - October 2011

If you don't need Java remove it.
 

8 More Discussions You Might Find Interesting

1. Solaris

disable telnet on Solaris

All - would you please some one help me to disable telnet on Solaris? /etc/inetd.conf Thanks :confused: (11 Replies)
Discussion started by: March_2007
11 Replies

2. Solaris

Disable all the logs in Solaris

Hi Is there anyway to disable all logs/logging (lastlog, sulog, messages etc.) in Solaris 9&10? I know this is not recommended but i just want to know if this is possible. TIA Reddy (8 Replies)
Discussion started by: reddyr
8 Replies

3. Red Hat

SSL/TLS renegotiation DoS -how to disable? Is it advisable to disable?

Hi all Expertise, I have following issue to solve, SSL / TLS Renegotiation DoS (low) 222.225.12.13 Ease of Exploitation Moderate Port 443/tcp Family Miscellaneous Following is the problem description:------------------ Description The remote service encrypts traffic using TLS / SSL and... (2 Replies)
Discussion started by: manalisharmabe
2 Replies

4. Red Hat

HOW TO DISABLE SSL/TLS RENEGOTIATION?

Hi guys, Those who work on Apache may help me on this. I have following problem Description: The remote service encrypts traffic using TLS / SSL and permits clients to renegotiate connections. The computational requirements for renegotiating a connection are asymmetrical between the... (3 Replies)
Discussion started by: manalisharmabe
3 Replies

5. Solaris

Solaris 11 disable IPv6

I've new installed Solaris 11 on Sparc T4-1. I'd like to disable IPv6 but with no luck. lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2 inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies

6. Solaris

How do I disable a core(or more) while boot up in Solaris 10?

Hi, I have 4 cores in my PC. I know how to disable a core using psradm -f command after boot up. But I want to disable while boot up (permanently). 1) I want only 1 core. How to disable all other cores while boot up? 2) I need to disable 2 cores. How to disable all other cores while boot... (5 Replies)
Discussion started by: sreejesh
5 Replies

7. Solaris

Can't disable CPU in Solaris

hello all i have an issue about a solaris V440 cpu, im logged in the Ok prompt i can't disable a CPU3, i can't see it in dev list, i see only the cpu3-bank0 to cpu-bank4 please help me to disable it thank youuu (3 Replies)
Discussion started by: walidadam
3 Replies

8. Solaris

How to configure CUPS on Solaris 11.3 - TLS and no TLS?

We are implementing CUPS on a new Solaris 11.3 system. The same system will run an application where users can print to networked printers inside our organisation, or to a printer outside of our organisation over the internet. For users printing to internal network printers, no encryption is... (0 Replies)
Discussion started by: SallyB
0 Replies
DACS.JAVA(7)						  DACS Miscellaneous Information					      DACS.JAVA(7)

NAME
dacs.java - DACS Java support DESCRIPTION
This document describes support for Java provided by DACS. To enable Java support, DACS must be configured using the --enable-java flag. It may also be necessary to specify the location of the Java commands and include files. See dacs.install(7)[1]. Note Java support is currently very limited and should be considered experimental. It is currently only possible to call dacsauth(1)[2] and dacscheck(1)[3] using the Java Native Interface (JNI) provided. The command line arguments to both of these commands are exactly as documented in their manual pages. Each argument is passed as a String. The code is not thread-safe and is probably not suitable for being called many times within a particular process due to assumptions it makes about dynamic memory allocation. There are no immediate plans to improve or extend Java support. Using the existing capability to build the JNI layer, however, it should not be difficult for an experienced Java programmer to build upon the example Java code provided. With Java support enabled, building DACS will copy the JNI shared library and a .jar file to the library directory (default: /usr/local/dacs/lib), and the JNI include files to the include directory (default: /usr/local/dacs/include). The tools/java/jni distribution directory contains a simple script called javarun that demonstrates how to run dacsauth or dacscheck as a Java application. For example, to validate the Unix password for user somebody, run (as root): ./javarun dacsauth -m unix suff -user somebody -prompt DIAGNOSTICS
The return codes are as documented in the command's manual page. AUTHOR
Distributed Systems Software (www.dss.ca[4]) COPYING
Copyright2003-2012 Distributed Systems Software. See the LICENSE[5] file that accompanies the distribution for licensing information. NOTES
1. dacs.install(7) http://dacs.dss.ca/man/dacs.install.7.html 2. dacsauth(1) http://dacs.dss.ca/man/dacsauth.1.html 3. dacscheck(1) http://dacs.dss.ca/man/dacscheck.1.html 4. www.dss.ca http://www.dss.ca 5. LICENSE http://dacs.dss.ca/man/../misc/LICENSE DACS 1.4.27b 10/22/2012 DACS.JAVA(7)
All times are GMT -4. The time now is 06:13 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy