Hi there
I have a file which has the lines
# Serial number for hostid
EXP_SERIAL_=""
These lines could be anywhere in the file as far as line numbers go, I would like replace these two lines with
# Serial number for hostid $var1
EXP_SERIAL_$var1="$var2"
Is there a quick and simple... (6 Replies)
I have searched the forum for this - forgive me if I missed a previous post.
I have the following file:
blah blah blah
blah blah blah
blah blah blah
blah blah blah
blah blah blah
alter table "informix".esc_acct add constraint (foreign key (fi_id)
references "informix".fi ... (5 Replies)
Hello experts,
I am new to this group and to 'SED' and 'AWK'. I have data (text file) with 5 columns (C_1-5) and 100s of lines (only 10 lines are shown below as an example). I have to find or select only the id numbers (C-1) of specific lines with '90' in the same line (of C_3) AND with '20' in... (6 Replies)
Hello,
I'm trying to figure out how to use sed or awk to delete single lines in a file. By single, I mean lines that are not touching any other lines (just one line with white space above and below).
Example:
one
two
three
four
five
six
seven
eight
I want it to look like: (6 Replies)
Hi,
I have a file with many lines,
then i have following list of lines(line number 5,12,19,5,and 28) i need to replace these lines of a file with another lines as shown below these text
contains special charecter like= (/:;){}
Line_number Text to replace with
5 abc... (1 Reply)
Hi friends,
This is sed & awk type question. It is slightly different from my previous question.
I have a text file which has numbers spread all over the file. I want to sum the series of numbers (but no more than 10 numbers in series) whenever i find it and produce an output file with the... (4 Replies)
Hi
I would like to know if it is possible to sum some specific fields.
I have this
x;x;x;x;x;x;x;x;467,390,611 Bytes;0.435291 GB;0.062247 GB;0.373045 GB;11,225;157
a;a;a;a;a;a;a;a;13,805,156,846 Bytes;12.857054 GB;1.838559 GB;11.018495 GB;151,063;18,933
b;b;b;b;b;b;b;b;232,797,478,723... (5 Replies)
Data file example
I look for primary and * to isolate the interesting slot number.
slot=`sed '/^primary$/,/\*/!d' filename | tail -1 | sed s'/*//' | awk '{print $1" "$2}'`
Now I want to get the Touch line for only the associate slot number, in this case, because the asterisk... (2 Replies)
Dear Unix Forums,
I am hoping you can help me with a pattern matching problem.
What am I trying to do?
I want to replace multiple lines of a text file (that match a multi-line pattern) with a single line of text. These patterns can span several lines and do not always have the same number of... (10 Replies)
In the awk piped to sed below I am trying to format file by removing the odd xxxx_digits and whitespace after, then move the even xxxx_digit to the line above it and add a space between them. There may be multiple lines in file but they are in the same format. The Filename_ID line is the last line... (4 Replies)
Discussion started by: cmccabe
4 Replies
LEARN ABOUT CENTOS
total
TOTAL(1) General Commands Manual TOTAL(1)NAME
total - sum up columns
SYNOPSIS
total [ -m ][ -sE | -p | -u | -l ][ -i{f|d}[N] ][ -o{f|d} ][ -tC ][ -N [ -r ]] [ file .. ]
DESCRIPTION
Total sums up columns of real numbers from one or more files and prints out the result on its standard output.
By default, total computes the straigt sum of each input column, but multiplication can be specified instead with the -p option. Likewise,
the -u option means find the upper limit (maximum), and -l means find the lower limit (minimum).
Sums of powers can be computed by giving an exponent with the -s option. (Note that there is no space between the -s and the exponent.)
This exponent can be any real number, positive or negative. The absolute value of the input is always taken before the power is computed
in order to avoid complex results. Thus, -s1 will produce a sum of absolute values. The default power (zero) is interpreted as a straight
sum without taking absolute values.
The -m option can be used to compute the mean rather than the total. For sums, the arithmetic mean is computed. For products, the geomet-
ric mean is computed. (A logarithmic sum of absolute values is used to avoid overflow, and zero values are silently ignored.)
If the input data is binary, the -id or -if option may be given for 64-bit double or 32-bit float values, respectively. Either option may
be followed immediately by an optional count, which defaults to 1, indicating the number of double or float binary values to read per
record on the input file. (There can be no space between the option and this count.) Similarly, the -od and -of options specify binary
double or float output, respectively. These options do not need a count, as this will be determined by the number of input channels.
A count can be given as the number of lines to read before computing a result. Normally, total reads each file to its end before producing
its result, but this behavior may be overridden by inserting blank lines in the input. For each blank input line, total produces a result
as if the end-of-file had been reached. If two blank lines immediately follow each other, total closes the file and proceeds to the next
one (after reporting the result). The -N option (where N is a decimal integer) tells total to produce a result and reset the calculation
after every N input lines. In addition, the -r option can be specified to override reinitialization and thus give a running total every N
lines (or every blank line). If the end of file is reached, the current total is printed and the calculation is reset before the next file
(with or without the -r option).
The -tC option can be used to specify the input and output tab character. The default tab character is TAB.
If no files are given, the standard input is read.
EXAMPLE
To compute the RMS value of colon-separated columns in a file:
total -t: -m -s2 input
To produce a running product of values from a file:
total -p -1 -r input
BUGS
If the input files have varying numbers of columns, mean values will certainly be off. Total will ignore missing column entries if the tab
separator is a non-white character, but cannot tell where a missing column should have been if the tab character is white.
AUTHOR
Greg Ward
SEE ALSO cnt(1), neaten(1), rcalc(1), rlam(1), tabfunc(1)RADIANCE 2/3/95 TOTAL(1)