06-22-2012
ok . that is 880 server .. assume eri0 is your interface and connect to lan cablr to interface .. otherwise you try
ifconfig eri0 plumb or
ifconfig ce0 or ce1 plumb
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I am trying to change an IP address on a machine running HPUX10
After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas??
Thanks
Brian (7 Replies)
Discussion started by: breigner
7 Replies
2. OS X (Apple)
Hi,
I type (as root) "ifconfig en1 ether aa:aa: " but it doesnt change the mac of my airport. Can anyone help me?
Thx. (0 Replies)
Discussion started by: Jariya
0 Replies
3. Solaris
I know that I could use the
#ifconfig hme0 plumb
to activate the network interface.
However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up?
I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
Discussion started by: heero
7 Replies
4. Shell Programming and Scripting
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
Discussion started by: moco
3 Replies
5. IP Networking
Hello everyone.
Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
Discussion started by: trutoman
9 Replies
6. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
7. Linux
Hi All,
I need some info on ifconfig.
ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux.
1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Discussion started by: ahamed101
2 Replies
8. Shell Programming and Scripting
Unable to run the ifconfig in my home dir..
I did add adding /sbin and /usr/sbin in th PATH
But still unable to get that ..
Am using red hat linux
cat /etc/redhat-release
Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
Discussion started by: mail2sant
3 Replies
9. Solaris
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
Discussion started by: Kjons76
3 Replies
10. Solaris
Hiii folks,,
I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.."
can someone help me...
Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies
EDSC(4) BSD Kernel Interfaces Manual EDSC(4)
NAME
edsc -- Ethernet discard network interface
SYNOPSIS
device edsc
DESCRIPTION
The edsc interface is a software discard mechanism which may be used for performance analysis and software testing. It imitates an Ethernet
device, which allows for its use in conjunction with such drivers as if_bridge(4) and vlan(4).
As with other network interfaces, an edsc interface must have network addresses assigned for each address family with which it is to be used.
These addresses may be set or changed with the SIOCSIFADDR ioctl(2) or ifconfig(8) utility.
Each edsc interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the
cloned_interfaces variable in rc.conf(5).
SEE ALSO
ioctl(2), arp(4), if_bridge(4), inet(4), intro(4), vlan(4), rc.conf(5), arp(8), ifconfig(8)
HISTORY
The edsc device was derived from the disc(4) device and first appeared in FreeBSD 6.3. This manpage was adapted from disc(4).
CAVEATS
Since outgoing packets are just discarded by edsc, ARP requests stay unreplied. Consequently, an IP packet cannot be sent via edsc until a
static arp(4) entry is created for its next hop using arp(8).
Initially an edsc interface has a zero link level address. It can be changed with ifconfig(8) lladdr if needed.
BSD
March 25, 2007 BSD