06-17-2012
I'd say that the driver is not seeing the card because the driver is either wrong or corrupt. Revert to card manufacturers instructions on installing the driver on this system.
Let's see what other suggestions are forthcoming from forum members.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I am trying to change an IP address on a machine running HPUX10
After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas??
Thanks
Brian (7 Replies)
Discussion started by: breigner
7 Replies
2. OS X (Apple)
Hi,
I type (as root) "ifconfig en1 ether aa:aa: " but it doesnt change the mac of my airport. Can anyone help me?
Thx. (0 Replies)
Discussion started by: Jariya
0 Replies
3. Solaris
I know that I could use the
#ifconfig hme0 plumb
to activate the network interface.
However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up?
I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
Discussion started by: heero
7 Replies
4. Shell Programming and Scripting
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
Discussion started by: moco
3 Replies
5. IP Networking
Hello everyone.
Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
Discussion started by: trutoman
9 Replies
6. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
7. Linux
Hi All,
I need some info on ifconfig.
ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux.
1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Discussion started by: ahamed101
2 Replies
8. Shell Programming and Scripting
Unable to run the ifconfig in my home dir..
I did add adding /sbin and /usr/sbin in th PATH
But still unable to get that ..
Am using red hat linux
cat /etc/redhat-release
Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
Discussion started by: mail2sant
3 Replies
9. Solaris
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
Discussion started by: Kjons76
3 Replies
10. Solaris
Hiii folks,,
I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.."
can someone help me...
Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies
LEARN ABOUT CENTOS
device
DEVICE(9) BSD Kernel Developer's Manual DEVICE(9)
NAME
device -- an abstract representation of a device
SYNOPSIS
typedef struct device *device_t;
DESCRIPTION
The device object represents a piece of hardware attached to the system such as an expansion card, the bus which that card is plugged into,
disk drives attached to the expansion card etc. The system defines one device, root_bus and all other devices are created dynamically during
autoconfiguration. Normally devices representing top-level busses in the system (ISA, PCI etc.) will be attached directly to root_bus and
other devices will be added as children of their relevant bus.
The devices in a system form a tree. All devices except root_bus have a parent (see device_get_parent(9)). In addition, any device can have
children attached to it (see device_add_child(9), device_add_child_ordered(9), device_find_child(9), device_get_children(9), and
device_delete_child(9)).
A device which has been successfully probed and attached to the system will also have a driver (see device_get_driver(9) and driver(9)) and a
devclass (see device_get_devclass(9) and devclass(9)). Various other attributes of the device include a unit number (see
device_get_unit(9)), verbose description (normally supplied by the driver, see device_set_desc(9) and device_get_desc(9)), a set of bus-spe-
cific variables (see device_get_ivars(9)) and a set of driver-specific variables (see device_get_softc(9)).
Devices can be in one of several states:
DS_NOTPRESENT the device has not been probed for existence or the probe failed
DS_ALIVE the device probe succeeded but not yet attached
DS_ATTACHED the device has been successfully attached
DS_BUSY the device is currently open
The current state of the device can be determined by calling device_get_state(9).
SEE ALSO
devclass(9), driver(9)
AUTHORS
This manual page was written by Doug Rabson.
BSD June 16, 1998 BSD