Something like this? Create a new script file every 20 lines from the input file. Each output script file contains 40 primary commands and 40 sleep commands. Untested. Output format and sleep values are based on your sample output format not on the original script.
Last edited by methyl; 06-16-2012 at 05:54 PM..
Reason: repost with correction
I'm using PartitionMagic's wizard to partition my drive for Linux, and after I get past the first step it asks if I want to screate a seperate Linux Swap Partition. What is a Linux Swap Partition and is something I need/should have? (10 Replies)
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Hi All..
Previously i've posted my question regarding this script and i managed to solve the problem but i need to modified my script so it will meet the new requirement.
Below is the script and output:
--------------------------------------------------------------
-bash-3.00$ more... (5 Replies)
Hi
I have an exam question which is below and I am looking for answer of this question:
I would appreciate your help.
* You are the systems administrator of a mail server that services approximately 3,000 users. 2,000
users access their email via a POP-3 service, while the remaining 1,000... (0 Replies)
Hi
I want to write a script, help me to monitor command output.
This script like Linux "watch" command.
Below is my script:
# cat watch.sh
#!/bin/bash
while true
do
clear
echo "command: $*"
( $* )
sleep 2
done
Then I run this script below (2 Replies)
OS : AIX 6.1
Shell : Korn
in the url
https://forums.oracle.com/forums/thread.jspa?threadID=361463&tstart=0
I came across a crontab entry example
00 23 * * 1,3,5 <complete shell script path> 1> <log file> 2>&1
From googling , I gathered that
0 - stdin
1 - stdout
2 - stderr
I... (5 Replies)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
LEARN ABOUT OPENDARWIN
pts_sleep
PTS_SLEEP(1) AFS Command Reference PTS_SLEEP(1)NAME
pts_sleep - Pauses for a few seconds
SYNOPSIS
pts sleep [-delay] <# of seconds>
[-cell] <cell name> [-noauth] [-localauth] [-force]
pts sl [-d] <# of seconds> [-c] <cell name>
[-n] [-l] [-f]
DESCRIPTION
The pts sleep pauses for a specified number of seconds. The command can be run from the command line or interactively, although from the
command line it's essentially equivalent to the sleep command. It is intended for use in interactive mode to pause for a few seconds
between batch commands to allow the Protection Server to catch up.
CAUTIONS
Prior to OpenAFS 1.4.5 and OpenAFS 1.5.23, the pts sleep command was only available on Unix or Linux and when OpenAFS was compiled with the
supergroups option (disabled by default). As of OpenAFS 1.4.5 and 1.5.23, it is always available.
OPTIONS
Although they have no effect, pts sleep takes the following standard pts options:
-cell <cell name>
Names the cell in which to run the command. For more details, see pts(1).
-force
Enables the command to continue executing as far as possible when errors or other problems occur, rather than halting execution at the
first error.
-help
Prints the online help for this command. All other valid options are ignored.
-localauth
Constructs a server ticket using a key from the local /etc/openafs/server/KeyFile file. Do not combine this flag with the -cell or
-noauth options. For more details, see pts(1).
-noauth
Assigns the unprivileged identity anonymous to the issuer. For more details, see pts(1).
OUTPUT
This command produces no output.
EXAMPLES
Here is an example of a pts interactive session:
% pts interactive
pts> sleep 5
pts> quit
%
SEE ALSO pts(1), pts_interactive(1)COPYRIGHT
Copyright 2007 Jason Edgecombe <jason@rampaginggeek.com>
This documentation is covered by the BSD License as written in the doc/LICENSE file. This man page was written by Jason Edgecombe for
OpenAFS.
OpenAFS 2014-04-08 PTS_SLEEP(1)