I am trying to change an IP address on a machine running HPUX10
After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas??
Thanks
Brian (7 Replies)
I know that I could use the
#ifconfig hme0 plumb
to activate the network interface.
However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up?
I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
Hello everyone.
Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Hi All,
I need some info on ifconfig.
ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux.
1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Unable to run the ifconfig in my home dir..
I did add adding /sbin and /usr/sbin in th PATH
But still unable to get that ..
Am using red hat linux
cat /etc/redhat-release
Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
Hiii folks,,
I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.."
can someone help me...
Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies
LEARN ABOUT HPUX
reboot
reboot(2) System Calls Manual reboot(2)NAME
reboot - boot the system
SYNOPSIS DESCRIPTION
causes the system to reboot. howto is a mask of reboot options (see specified as follows:
A file system sync is performed (unless
is set) and the processor is rebooted from the default device and file.
The processor is simply halted.
A sync of the file system is performed unless the flag is set. should be used with caution.
On systems with cellular architecture, all cells in the partition are
rebooted in order to reconfigure the stable complex configuration data. On systems with non-cellular architec-
ture, the default is A sync of the file system is performed unless the flag is set.
Shut down the system firmware to a "ready to reconfigure" state and do not
reboot. This option can be used only in combination with
A sync of the file system is not performed.
Unless the flag has been specified, reboot(2) unmounts all mounted file systems and marks them clean so that it will not be necessary to
run fsck(1M) on these file systems when the system reboots.
Only users with appropriate privileges can reboot a machine.
RETURN VALUE
If successful, this call never returns. Otherwise, a -1 is returned and is set to indicate the error.
ERRORS
fails if this condition is encountered:
[EPERM] The effective user ID of the caller is not a user with appropriate privileges.
DEPENDENCIES
The default file and device for is on the current root device.
AUTHOR
was developed by HP and the University of California, Berkeley.
SEE ALSO reboot(1M), privileges(5).
reboot(2)