Sponsored Content
Full Discussion: ifconfig ge0 plumb
Operating Systems Solaris ifconfig ge0 plumb Post 302657087 by hicksd8 on Saturday 16th of June 2012 06:49:13 AM
Old 06-16-2012
Strange!!

The "ge" driver seems to be on the system because it's listed in path_to_inst

Does the file /etc/hostname.ge0 exist? If not, create it with the required hostname in it. Also check that hostname appears in /etc/hosts with its required ip address.

Reboot the system including the -r (reconfigure) switch

Code:
 
boot -r

Does the boot sequence still report "cannot plumb ge0"?
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

ifconfig

I am trying to change an IP address on a machine running HPUX10 After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas?? Thanks Brian (7 Replies)
Discussion started by: breigner
7 Replies

2. OS X (Apple)

ifconfig

Hi, I type (as root) "ifconfig en1 ether aa:aa: " but it doesnt change the mac of my airport. Can anyone help me? Thx. (0 Replies)
Discussion started by: Jariya
0 Replies

3. Solaris

Before plumb the network interface.....

I know that I could use the #ifconfig hme0 plumb to activate the network interface. However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up? I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
Discussion started by: heero
7 Replies

4. Shell Programming and Scripting

ifconfig!!!!

why the ifconfig command is not working in my machine? it says "-bash: ifconfig: command not found" why its says that? actually i m looking for "how can I know the Network Interface Card physical address?" Requesting u all for help. thanks (3 Replies)
Discussion started by: moco
3 Replies

5. IP Networking

/etc/hosts changes when ifconfig......

Hello everyone. Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
Discussion started by: trutoman
9 Replies

6. Solaris

cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file. getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies

7. Linux

ifconfig - information

Hi All, I need some info on ifconfig. ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux. 1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Discussion started by: ahamed101
2 Replies

8. Shell Programming and Scripting

not able to run ifconfig

Unable to run the ifconfig in my home dir.. I did add adding /sbin and /usr/sbin in th PATH But still unable to get that .. Am using red hat linux cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
Discussion started by: mail2sant
3 Replies

9. Solaris

Ifconfig command ?

What would be the command to remove the IP address from an interface? I want to remove the ip from this interface: ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5 inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79 ether 0:3:ba:da:a6:96 (3 Replies)
Discussion started by: Kjons76
3 Replies

10. Solaris

ifconfig hme0 plumb not working

Hiii folks,, I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.." can someone help me... Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies
check-hostname(1M)					  System Administration Commands					check-hostname(1M)

NAME
check-hostname - check if sendmail can determine the system's fully-qualified host name SYNOPSIS
/usr/sbin/check-hostname DESCRIPTION
The check-hostname script is a migration aid for sendmail(1M). This script tries to determine the local host's fully-qualified host name (FQHN) in a manner similar to sendmail(1M). If check-hostname is able to determine the FQHN of the local host, it reports success. Other- wise, check-hostname reports how to reconfigure the system so that the FQHN can be properly determined. FILES
/etc/hosts Host name database /etc/nsswitch.conf Name service switch configuration file /etc/resolv.conf Configuration file for name server routines ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWsndmu | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
domainname(1M), sendmail(1M), hosts(4), attributes(5) SunOS 5.11 8 Mar 2006 check-hostname(1M)
All times are GMT -4. The time now is 06:46 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy