The "ge" driver seems to be on the system because it's listed in path_to_inst
Does the file /etc/hostname.ge0 exist? If not, create it with the required hostname in it. Also check that hostname appears in /etc/hosts with its required ip address.
Reboot the system including the -r (reconfigure) switch
Does the boot sequence still report "cannot plumb ge0"?
I am trying to change an IP address on a machine running HPUX10
After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas??
Thanks
Brian (7 Replies)
I know that I could use the
#ifconfig hme0 plumb
to activate the network interface.
However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up?
I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
Hello everyone.
Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Hi All,
I need some info on ifconfig.
ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux.
1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Unable to run the ifconfig in my home dir..
I did add adding /sbin and /usr/sbin in th PATH
But still unable to get that ..
Am using red hat linux
cat /etc/redhat-release
Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
Hiii folks,,
I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.."
can someone help me...
Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies
LEARN ABOUT OPENSOLARIS
install-solaris
install-solaris(1M)install-solaris(1M)NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)