Could you please post the output of below commands?
You cannot increase the size of a ZFS file system by setting quota. That's really a very wrong idea. Quota is a way to set a hard limit on the maximum size of the ZFS file system.
How did you add the LUNs to the zpool? You need to check the total pool size with the "zpool list" command. If you want to see the underlying ZFS volume's size, use "zfs list" command. Data provided by df command for ZFS filesystems is kind of misleading due to the whole pooling concept.
Hi,
I am getting an error message when i try to increase the size of a filesystems
under AIX 4.3.3:
chfs: 0506-932 Can not extend a JFS file system with nbpi = 4096
and frag = 4096 past 134217728 (512 byte blocks).
-> Characteristics Journaled File System
... (4 Replies)
Hi,
I try add a new file system:
#zfs create dsk1/mqm
it came back with:
#cannot create 'dsk1/mqm': no such pool 'dsk1'
what do I have to do?
Kind regards
Mehrdad (2 Replies)
Hi All,
I am using this commands to dynamically increase ZFS swap space on Solaris
my question is:
1- after i make these commands it will permanent or it will remove after restart
2- how to make it permanent
# swap -l
swapfile dev swaplo bloques libre
/dev/zvol/dsk/rpool/swap... (4 Replies)
Hi,
I have Solaris-10 (Update-7). This is having ZFS file-system and 10 sparse-root zones are there. I want to install Solaris-10 recommended patch cluster on it, but not sure, how to go ahead with procedure. I want to patch one side of the mirror and keep intact another side safe in case of... (6 Replies)
Hi All
I want to extend this file system to 120Gb:
df -h /xyz
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d80 98G 35G 62G 37% /xyzand the NetApp admin is going to give me an LUN with 22Gb.
This file system is mounted on:
metastat d80... (1 Reply)
I have Solaris-10 server running ZFS file-system. ctdp04_vs03-pttmsp01 is one of the non global zone. I wanted to increase a /ttms/prod file-system of zone, which is actually /zone/ctdp04_vs03-pttmsp01/ttms/prod on global server.
I have added a new disk of 9 GB, which is emcpower56a and now I can... (16 Replies)
Hi
I have the following file system, that needs to be expanded to more 500Gb, so a total of 1Tb:
df -h /oradata1
Filesystem Size Used Available Capacity Mounted on
oradata1 587G 517G 69G 89% /oradata1
I am not familiar with zfs, I am more... (17 Replies)
Hi,
I have inherited this AIX 5.3 host. I'm unable to increase the /usr file system. It gives me this error.
What needs to be done to remove this error?
vios:/home/padmin$ chfs -a size=+128M /usr
0516-304 lquerypv: Unable to find device id 0002ef4df616f9690000000000000000 in the Device
... (14 Replies)
Hello,
Need to ask the question regarding extending the zfs storage file system.
currently after using the command, df -kh
u01-data-pool/data 600G 552 48G 93% /data
/data are only 48 gb remaining and it has occupied 93% for total storage.
zpool u01-data-pool has more then 200 gb... (14 Replies)
Discussion started by: shahzad53
14 Replies
LEARN ABOUT FREEBSD
zfsboot
ZFSBOOT(8) BSD System Manager's Manual ZFSBOOT(8)NAME
zfsboot -- bootcode for ZFS on BIOS-based computers
DESCRIPTION
zfsboot is used on BIOS-based computers to boot from a filesystem in a ZFS pool. zfsboot is installed in two parts on a disk or a partition
used by a ZFS pool. The first part, a single-sector starter boot block, is installed at the beginning of the disk or partition. The second
part, a main boot block, is installed at a special offset within the disk or partition. Both areas are reserved by the ZFS on-disk specifi-
cation for boot use. If zfsboot is installed in a partition, then that partition should be made bootable using appropriate configuration and
boot blocks described in boot(8).
BOOTING
The zfsboot boot process is very similar to that of gptzfsboot(8). One significant difference is that zfsboot does not currently support the
GPT partitioning scheme. Thus only whole disks and MBR partitions, traditionally referred to as slices, are probed for ZFS disk labels. See
the BUGS section in gptzfsboot(8) for some limitations of the MBR scheme support.
USAGE
zfsboot supports all the same prompt and configuration file arguments as gptzfsboot(8).
FILES
/boot/zfsboot boot code binary
/boot.config parameters for the boot block (optional)
/boot/config alternative parameters for the boot block (optional)
EXAMPLES
zfsboot is typically installed using dd(1). To install zfsboot on the ada0 drive:
dd if=/boot/zfsboot of=/dev/ada0 count=1
dd if=/boot/zfsboot of=/dev/ada0 iseek=1 oseek=1024
If the drive is currently in use, the GEOM safety will prevent writes and must be disabled before running the above commands:
sysctl kern.geom.debugflags=0x10
zfsboot can also be installed in an MBR slice:
gpart create -s mbr ada0
gpart add -t freebsd ada0
gpart create -s BSD ada0s1
gpart bootcode -b /boot/boot0 ada0
gpart set -a active -i 1 ada0
dd if=/boot/zfsboot of=/dev/ada0s1 count=1
dd if=/boot/zfsboot of=/dev/ada0s1 iseek=1 oseek=1024
Note that commands to create and populate a pool are not shown in the example above.
SEE ALSO dd(1), boot.config(5), boot(8), gptzfsboot(8), loader(8), zfsloader(8), zpool(8)HISTORY
zfsboot appeared in FreeBSD 7.3.
AUTHORS
This manual page was written by Andriy Gapon <avg@FreeBSD.org>.
BUGS
Installing zfsboot with dd(1) is a hack. ZFS needs a command to properly install zfsboot onto a ZFS-controlled disk or partition.
BSD September 15, 2014 BSD