SCP(1)							    BSD General Commands Manual 						    SCP(1)

NAME

     scp -- secure copy (remote file copy program)

SYNOPSIS

     scp [-346BCpqrv] [-c cipher] [-F ssh_config] [-i identity_file] [-l limit] [-o ssh_option] [-P port] [-S program] source ... target

DESCRIPTION

     scp copies files between hosts on a network.  It uses ssh(1) for data transfer, and uses the same authentication and provides the same secu-
     rity as ssh(1).  scp will ask for passwords or passphrases if they are needed for authentication.

     The source and target may be specified as a local pathname, a remote host with optional path in the form [user@]host:[path], or a URI in the
     form scp://[user@]host[:port][/path].  Local file names can be made explicit using absolute or relative pathnames to avoid scp treating file
     names containing ':' as host specifiers.

     When copying between two remote hosts, if the URI format is used, a port may only be specified on the target if the -3 option is used.

     The options are as follows:

     -3      Copies between two remote hosts are transferred through the local host.  Without this option the data is copied directly between the
	     two remote hosts.	Note that this option disables the progress meter.

     -4      Forces scp to use IPv4 addresses only.

     -6      Forces scp to use IPv6 addresses only.

     -B      Selects batch mode (prevents asking for passwords or passphrases).

     -C      Compression enable.  Passes the -C flag to ssh(1) to enable compression.

     -c cipher
	     Selects the cipher to use for encrypting the data transfer.  This option is directly passed to ssh(1).

     -F ssh_config
	     Specifies an alternative per-user configuration file for ssh.  This option is directly passed to ssh(1).

     -i identity_file
	     Selects the file from which the identity (private key) for public key authentication is read.  This option is directly passed to
	     ssh(1).

     -l limit
	     Limits the used bandwidth, specified in Kbit/s.

     -o ssh_option
	     Can be used to pass options to ssh in the format used in ssh_config(5).  This is useful for specifying options for which there is no
	     separate scp command-line flag.  For full details of the options listed below, and their possible values, see ssh_config(5).

		   AddressFamily
		   BatchMode
		   BindAddress
		   BindInterface
		   CanonicalDomains
		   CanonicalizeFallbackLocal
		   CanonicalizeHostname
		   CanonicalizeMaxDots
		   CanonicalizePermittedCNAMEs
		   CertificateFile
		   ChallengeResponseAuthentication
		   CheckHostIP
		   Ciphers
		   Compression
		   ConnectionAttempts
		   ConnectTimeout
		   ControlMaster
		   ControlPath
		   ControlPersist
		   GlobalKnownHostsFile
		   GSSAPIAuthentication
		   GSSAPIDelegateCredentials
		   HashKnownHosts
		   Host
		   HostbasedAuthentication
		   HostbasedKeyTypes
		   HostKeyAlgorithms
		   HostKeyAlias
		   HostName
		   IdentitiesOnly
		   IdentityAgent
		   IdentityFile
		   IPQoS
		   KbdInteractiveAuthentication
		   KbdInteractiveDevices
		   KexAlgorithms
		   LogLevel
		   MACs
		   NoHostAuthenticationForLocalhost
		   NumberOfPasswordPrompts
		   PasswordAuthentication
		   PKCS11Provider
		   Port
		   PreferredAuthentications
		   ProxyCommand
		   ProxyJump
		   PubkeyAcceptedKeyTypes
		   PubkeyAuthentication
		   RekeyLimit
		   SendEnv
		   ServerAliveInterval
		   ServerAliveCountMax
		   StrictHostKeyChecking
		   TCPKeepAlive
		   UpdateHostKeys
		   UsePrivilegedPort
		   User
		   UserKnownHostsFile
		   VerifyHostKeyDNS

     -P port
	     Specifies the port to connect to on the remote host.  Note that this option is written with a capital 'P', because -p is already
	     reserved for preserving the times and modes of the file.

     -p      Preserves modification times, access times, and modes from the original file.

     -q      Quiet mode: disables the progress meter as well as warning and diagnostic messages from ssh(1).

     -r      Recursively copy entire directories.  Note that scp follows symbolic links encountered in the tree traversal.

     -S program
	     Name of program to use for the encrypted connection.  The program must understand ssh(1) options.

     -v      Verbose mode.  Causes scp and ssh(1) to print debugging messages about their progress.  This is helpful in debugging connection,
	     authentication, and configuration problems.

EXIT STATUS

     The scp utility exits 0 on success, and >0 if an error occurs.

SEE ALSO

     sftp(1), ssh(1), ssh-add(1), ssh-agent(1), ssh-keygen(1), ssh_config(5), sshd(8)

HISTORY

     scp is based on the rcp program in BSD source code from the Regents of the University of California.

AUTHORS

     Timo Rinne <tri@iki.fi>
     Tatu Ylonen <ylo@cs.hut.fi>

BSD
								 February 23, 2018							       BSD